2025-03-10

Aileron - arrière (adaptation à l’aide de gabarit)

Code de correction 12220416 0.30 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 2025-03-03: Added wet-out instructions, video of wet-out process, and noted that adhesion promoter SHOULD NOT be used.
  • 1479070-00-A Trousse, alignement aileron, M3

Procédure

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
N'appliquez pas de promoteur d'adhésion au couvercle du coffre, puisque cela pourrait nuire à l'adhésion du ruban de l'aileron et/ou endommager la peinture.
  1. Clean the spoiler installation surface with isopropyl alcohol (IPA) wipes, and allow it to dry before continuing.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean any moisture or contaminates that might be present from rain or vehicle washing, otherwise this might result in poor adhesion of the rear spoiler.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the trunk surface requires any paint correction, request assistance from the body shop or shop detailer before the installation of the rear spoiler.
    Informational PurposesAn informational icon, calling your attention
    Note
    The acceptable ambient and part temperature for installation is 15-43 degrees Celsius (60-110 degrees Fahrenheit) for proper adhesion.
  2. Open the trunk.
  3. Place the spoiler jigs special tool on the LH and RH edges of the trunk lid, and then secure them with masking tape.
    Informational PurposesAn informational icon, calling your attention
    Note
    The spoiler jigs are used to center and align the spoiler and are removed from the vehicle prior to installation.
    Figure 1. LH side shown, RH similar
  4. Place shop towels on the LH and RH bump stops to keep the trunk from latching, and then partially close the trunk.
  5. Dry fit the rear spoiler between the spoiler jigs special tool.
    Figure 2. LH shown, RH similar
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not remove the spoiler adhesive tape backing at this time.
  6. Apply masking tape to the center of the rear spoiler and the trunk lid, and then mark approximately 25 mm spacing between the centering lines on the masking tape using a paint marker.
  7. Remove the spoiler jigs special tool.
  8. Verify the rear spoiler fitment on the trunk lid.
    Informational PurposesAn informational icon, calling your attention
    Note
    Each rear spoiler might have a slight different contour. Make sure the rear spoiler is centered on the trunk lid and its corners are laying flat.
  9. Cut the masking tape to allow removal of the rear spoiler.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not damage the surfaces of the trunk lid or rear spoiler while using a plastic razor blade.
  10. Remove the rear spoiler from the trunk lid.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    N'appliquez pas de promoteur d'adhésion au couvercle du coffre, puisque cela pourrait nuire à l'adhésion du ruban de l'aileron et/ou endommager la peinture.
  11. Remove the adhesive backing from the rear spoiler.
  12. Align the two marks on the masking tape on the rear spoiler with the two marks on the masking tape on the trunk lid. Hold the corners of the rear spoiler away from the trunk lid to install the center section of the rear spoiler first.
  13. Secure each end of the rear spoiler to the trunk lid.
  14. Wet out the adhesive: working on one small section at a time, apply > 20 pounds of pressure for 10 seconds on the spoiler. Wet out the entire length of the spoiler, with extra emphasis on the ends of the spoiler.
  15. Remove the masking tape from the vehicle, and then clean the work area.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the rear spoiler corners are laid flat to the trunk lid and symmetrical.
  16. Perform a configuration update.