2025-03-10

Boucle – deuxième rangée – gauche (retrait et remplacement)

Code de correction 20057002 0.18 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 2152873-00-A Tool, Inductive Heating

Caractéristiques techniques de couple

Tableau 1. Caractéristiques techniques de couple : Boucle – deuxième rangée – gauche (retrait et remplacement)
Description Valeur de couple Outils recommandés Réutiliser/remplacer Remarques
Boulon de raccordement qui fixe la boucle gauche à la carrosserie du véhicule
40 Nm (29.5 lbs-ft)
  • Douille de 15 mm
  • Rallonge de 3 po
  • Outil à chauffage inductif (au besoin)
Remplacer Le boulon est raccordé. Vous pouvez utiliser l’outil de chauffage inductif si le boulon est difficile à enlever.

Retirer

  1. Remove the 2nd row lower seat cushion. See Coussin de siège - inférieur - appuie-tête - 2e rangée (retirez et remplacez).
  2. Disconnect the LH rear seat belt buckle electrical connector.
  3. Release the plastic bracket that attaches the female side of the electrical connector to the body studs.
  4. Remove and discard the bolt that attaches the LH 2nd row buckle to the body, and then remove the buckle from the vehicle.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    If the bolt is hard to remove, use an inductive heating tool to melt the adhesive patch material. Position the inductive heating tool coil around the bolt, and then heat the bolt for 20 seconds. Allow the bolt to cool down for 2 minutes, and then remove and discard the bolt. The inductive heater coil, bolt, and adjacent areas will be extremely hot.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Persons that have a pacemaker or any other kind of electronic or metal surgical implant must stay at least 1 m (3 ft) away from the inductive heater while it is in use.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Remove all metallic items (such as coins, keys, electronics, and tools) from pockets before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Ensure that there is a properly-maintained fire extinguisher in the work area before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use the inductive heater in a well-ventilated area.
    Callout Description
    1 LH 2nd Row Buckle on Top
    2 Center 2nd Row Seatbelt Anchor in the Middle
    3 LH Inner Ancillary Bay Rail at the Bottom

Installer

  1. This video shows how to properly stack the 2nd row LH seat buckle onto the 2nd row center seat belt anchor:
  2. Set the 2nd row center seat belt anchor onto the 2nd row LH inner ancillary bay rail, with the belt to the RH side.
  3. Make sure that the belt is not twisted, and lays flat against the 2nd row seatback.
  4. Set the guide pin of the 2nd row LH seat buckle bracket into the hole of the 2nd row LH inner ancillary bay rail, and pivot the bracket down onto the anchor, aligning the guide pin to the slot in the anchor.
  5. Install a new bolt to attach the seat buckle bracket, the seat belt anchor, and the inner ancillary bay rail to the body.
    40 Nm (29.5 lbs-ft)
  6. Verify the stacking.
    Callout Description
    1 LH 2nd Row Buckle on Top
    2 Center 2nd Row Seatbelt Anchor in the Middle
    3 LH Inner Ancillary Bay Rail at the Bottom
  7. Install the plastic bracket that attaches the female side of the electrical connector to the body studs.
  8. Connect the LH rear seat belt buckle electrical connector.
  9. Install the 2nd row lower seat cushion. See Coussin de siège - inférieur - appuie-tête - 2e rangée (retirez et remplacez).