2026-09-02

Tire Rotation (Mobile Only)

Code de correction 34020105 FRT 0.48 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps à taux fixe (FRT) connexe représentent tout le travail à accomplir pour cette procédure, y compris les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

  • 2026-08-27: Released new procedure.
Remarque
Cette procédure s'applique aux véhicules munis de roues de mêmes tailles et de pneus non directionnels. Vous trouverez ci-dessous des conseils sur la rotation des roues de tailles différentes ou des pneus directionnels :
  • Roues de tailles différentes avec pneus non directionnels. Pour faire tourner les pneus avant, soulevez l'avant gauche et l'avant droit du véhicule à l'aide d'un cric; pour faire tourner les pneus arrière, soulevez l'arrière gauche et l'arrière droit du véhicule à l'aide d'un cric :
  • Roues de mêmes tailles avec pneus directionnels. Pour faire tourner les pneus du côté gauche, soulevez l'avant gauche et l'arrière gauche du véhicule à l'aide d'un cric; pour faire tourner les pneus du côté droit, soulevez l'avant droit et l'arrière droit du véhicule à l'aide d'un cric :

Vehicle ride quality and handling are maximized when all 4 tires are the same age, model, and tread depth. Rotating tires regularly allows them to wear at the same rate and increases the service life. Tesla recommends tire rotation every 6,250 miles (10,000 km) or if tread depth difference is 2/32 in (1.5mm) or greater, whichever comes first.

Remarque
Tesla recommends replacing tires in pairs unless the other tires are within 2/32 in (1.5 mm) of tread depth of the new tire.
Remarque
If only 2 new tires are installed, the new tires must be installed on the rear of the vehicle. In wet conditions, the tires that have less tread have less traction than the new tires. Reduced traction at the front of the vehicle leads to understeer, which most drivers are better able to react to than the oversteer that would result if the worn tires were on the rear of the vehicle.
Remarque
Tesla recommends replacing a tire if any of the tread depths are 4/32 in (3 mm) or less.
Remarque
Model Y is pictured, but this procedure can be performed on Model 3.

Procédure

  1. Ensure the vehicle is parked on a level surface.
  2. Install wheel chocks on the RH front wheel.
  3. Remove the LH rear wheel cap, if equipped. See Bouchon - volant (retirez et remplacez).
  4. Loosen LH rear wheel lug nuts (x5)
    Remarque
    5x nuts, 21mm, 175 Nm
    ATTENTION
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  5. Remove the LH front wheel cap. See Bouchon - volant (retirez et remplacez).
  6. Loosen LH front wheel lug nuts (x5).
    Remarque
    5x nuts, 21mm, 175 Nm
    ATTENTION
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  7. Jack up the LH rear of the vehicle.
    Remarque
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    Remarque
    Raise the vehicle until the LH front wheel is off the ground.
  8. Position jack stands underneath the LH front and LH rear of the vehicle.
    ATTENTION
    Si un cric électrique ou pneumatique est utilisé, restez à l'écart du véhicule avant de le soulever pour éviter les blessures.
    Remarque
    Align the jack stand cutout with the floor jack.
    Remarque
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  9. Slowly lower the floor jacks, making sure the LH front and rear jack stands are aligned with the jack stand adapters.
    Remarque
    Perform a shake test to verify stability.
  10. Remove the lug nuts from the wheel, and then remove the LH rear wheel from the vehicle.
    Remarque
    5x nuts, 21mm, 175 Nm
  11. Remove the lug nuts from the wheel, and then remove the LH front wheel from the vehicle.
    Remarque
    5x nuts, 21mm, 175 Nm
  12. Swap the LH rear wheel with the LH front wheel and install the LH wheels.
    Remarque
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    Avertissement
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  13. Raise the vehicle off the LH rear and LH front jack stands.
    Remarque
    Jack up the LH rear of the vehicle until the LH front wheel is off the jack stand.
  14. Remove the LH front and LH rear jack stands (x2), and then lower the vehicle.
  15. Remove the chocks from the RH front wheel.
  16. Install wheel chocks on the LH front wheel.
  17. Remove the RH rear wheel cap. See Bouchon - volant (retirez et remplacez).
  18. Loosen RH rear wheel lug nuts (x5).
    Remarque
    5x nuts, 21mm, 175 Nm
    ATTENTION
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  19. Remove the RH front wheel cap. See Bouchon - volant (retirez et remplacez).
  20. Loosen RH front wheel lug nuts (x5).
    Remarque
    5x nuts, 21mm, 175 Nm
    ATTENTION
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  21. Jack up the RH rear of the vehicle.
    Remarque
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    Remarque
    Raise the vehicle until the RH front wheel is off the ground.
  22. Position jack stands underneath the RH front and RH rear of the vehicle.
    ATTENTION
    Si un cric électrique ou pneumatique est utilisé, restez à l'écart du véhicule avant de le soulever pour éviter les blessures.
    Remarque
    Align the jack stand cutout with the floor jack.
    Remarque
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  23. Slowly lower the floor jacks, making sure the RH front and rear jack stands are aligned with the jack stand adapters.
    Remarque
    Perform a shake test to verify stability.
  24. Remove the lug nuts from the wheel, and then remove the RH rear wheel from the vehicle.
    Remarque
    5x nuts, 21mm, 175 Nm
  25. Remove the lug nuts from the wheel, and then remove the RH front wheel from the vehicle.
    Remarque
    5x nuts, 21mm, 175 Nm
  26. Swap the RH rear wheel with the RH front wheel and install the RH wheels.
    Remarque
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    Avertissement
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  27. Raise the vehicle off the RH rear and RH front jack stands.
    Remarque
    Jack up the RH rear of the vehicle until the RH front wheel is off the jack stand.
  28. Remove the RH front jack stand, and then lower the vehicle.
  29. Jack up the LH rear of the vehicle.
    Remarque
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
  30. Slowly lower the floor jack, making sure the LH rear jack stand is aligned with the jack stand adapter.
    Remarque
    Perform a shake test to verify stability.
  31. Remove the lug nuts from the wheel, and then remove the LH rear wheel from the vehicle.
    Remarque
    5x nuts, 21mm, 175 Nm
  32. Remove the lug nuts from the wheel, and then remove the RH rear wheel from the vehicle.
    Remarque
    5x nuts, 21mm, 175 Nm
  33. Swap the RH rear wheel with the LH rear wheel and install the rear wheels.
    Remarque
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    Avertissement
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  34. Remove the LH rear jack stand, and then lower the vehicle.
  35. Remove the RH rear jack stand and then lower the vehicle.
  36. Torque all 4 rear wheels.
    Remarque
    5x nuts, 21mm, 175 Nm
  37. Install all 4 wheel caps. See Bouchon - volant (retirez et remplacez).
  38. Remove the chocks from the LH front wheel.
  39. Open the LH front door.
  40. Unlock vehicle gateway. See Passerelle (déverrouiller).
  41. Tap Controls > Chassis > Alignment & Tire > Reset Learned Tire Values, and click Run.
    Remarque
    Click Close once the routine is completed.
  42. Tap Controls > Service > Wheel & Tire > Tires, choose the tire season and click Reset. After resetting, check if the Tire Service Mileage in the upper right corner is displayed as Less than 500 km ago.
  43. Exit Service Mode.
  44. Close the LH Front door.
  45. Inform the customers that a short calibration drive cycle might be required.