Code de correction 15302602 15302601 FRT 0.42 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

1. Open all four doors
   Remarque

   If vehicle is being powered down, Latch rear doors to prevent accidental closure

   

2. Lower all four windows

   

3. Move LH front seat forward

   

4. Move RH front seat forward

   

5. Remove 2nd row seat cushion
   Remarque

   2x tabs, 2x connectors, Slide locking tabs to left of vehicle while lifting up seat bench. Newer models have connectors on both sides of bench, Older models have 2x connectors on one side of bench

   

   

   

   

   

   

   

   

6. Open liftgate from exterior switch

   

7. Remove load floor
   Remarque

   Use pull tab located at rear edge of panel

   

   

8. Remove trunk sill trim assembly
   Remarque

   4x clips, 1x location pin, Pull corner upward release clip on the end the away from body for remaining clips

   

   

9. Remove clips securing rear trunk carpet
   Remarque

   2x push clips

   

10. Remove rear trunk carpet from vehicle
    Remarque

    4x velcro strips

    

    

11. Remove LH rear seat belt buckle
    Remarque

    1x patch bolt, 15mm, 40 Nm, If the bolt is difficult to remove, Use an inductive heating tool to melt the adhesive patch material, Position the inductive heating tool coil around the bolt, then heat the bolt for 20 seconds, Allow the bolt to cool for 2 minutes, Discard after removal

    

    

12. Fold 60 seat in down position
    Remarque

    Protect the seat cushion

    

13. Remove LH side bolster
    Remarque

    1x clip, 2x location pins, Pull outward then slightly upward to remove

    

    

14. Remove and discard bolster plastic bracket from RH side
    Remarque

    2x clips, If necessary, depress the clips from behind, this bracket may come out with bolster. Discard after removal

    

15. Fold 60 seat into vertical position
    Remarque

    Remove seat protection

    

16. Disconnect 60 seat back seat heater harness
    Remarque

    1x connector

    

17. Remove nuts securing 60 seat back hinge bracket to body
    Remarque

    2x nuts, 13mm, 18 Nm

    

18. Remove 60 seat back by lifting up on LH side and pulling inner pivot out of 40 seat back and set onto padded work surface

    

19. Fold 40 seat in down position
    Remarque

    Protect the seat cushion

    

20. Remove RH side bolster
    Remarque

    1x clip, 1 tab, Pull outward then slightly upward to remove

    

21. Remove and discard bolster plastic bracket from LH side
    Remarque

    2x clips, If necessary, depress the clips from behind, This bracket may come out with bolster, Discard after removal

    

22. Disconnect 40 seat back seat heater harness
    Remarque

    1x connector

    

23. Remove nuts securing 40 seat back hinge bracket to body
    Remarque

    2x nuts, 13mm, 18 Nm

    

24. Remove 40 seat back from vehicle
    Remarque

    Lift bracket from studs and slide outward

    

25. Remove front trunk carpet from vehicle
    Remarque

    2x clips, Lift trunk carpet off of isofix bars

    

    

26. Install front trunk carpet into vehicle
    Remarque

    2x clips, Align the trunk carpet to isofix bars

    

    

27. Install 60 seat back to vehicle
    Remarque

    Align center and outer pivot locations

    

28. Install nuts securing 60 seat back hinge bracket to body
    Remarque

    2x nuts, 13mm, 18 Nm

    

29. Connect 60 seat back seat heater harness
    Remarque

    1x connector

    

30. Install bolt securing LH seat belt catch and center seat belt to vehicle
    Remarque

    1x patch bolt, 15mm, 40 Nm, Install new patch bolt, Position center seat belt under buckle, Make sure the guide pin is aligned

    

31. Fold 60 seat in down position
    Remarque

    Protect the seat cushion if necessary

    

32. Install bolster plastic bracket to LH side bolster
    Remarque

    2x tabs, Install new bolster bracket

    

33. Install LH side bolster
    Remarque

    1x clip, 2x location pins, Align the bottom tab then push inward to install

    

    

34. Fold 60 seat into vertical position
    Remarque

    Remove seat cushion protection, Be careful not to pinch the seat belt

    

35. Install 40 seat back to vehicle
    Remarque

    Align center and outer pivot locations

    

36. Install nuts securing 40 seat back hinge bracket to body
    Remarque

    2x nuts, 13mm, 18 Nm

    

37. Connect 40 seat back seat heater harness
    Remarque

    1x connector

    

38. Fold the 40 seat in down position
    Remarque

    Protect the seat cushion if necessary

    

39. Install bolster plastic bracket to RH side bolster
    Remarque

    2x tabs, Install new bolster bracket

    

40. Install RH side bolster
    Remarque

    1x clip, 1x tab, Align the bottom tab then push inward to install

    

41. Fold seat into vertical position
    Remarque

    Remove seat cushion protection

    

42. Install rear trunk carpet into vehicle
    Remarque

    4x velcro strips, Fully seat carpet at velcro strips

    

    

43. Install clips securing trunk carpet
    Remarque

    2x push clips

    

44. Install trunk sill trim assembly
    Remarque

    4x clips, 1x location pin, Align the latch with center slot then 2 locator to their slot and then press to secure the clips, Adjust the seal to overlap the trim

    

    

    

    

45. Install load floor

    

    

46. Close trunk

    

    

47. Connect 2nd row seat cushion harness and install 2nd row seat cushion
    Remarque

    2x connectors, 2x clips, Insert the seat belt buckles through the holes, Slide rear cushion inward then align front guide tabs to locking tabs, Make sure cushion is fully seated with push pull test near clips

    

    

    

    

    

    

    

    

48. Move RH front seat to original position

    

49. Move LH front seat to original position

    

50. Raise all four windows

    

51. Close all four doors