2025-03-10
Module - commande de la carrosserie - sécurité (retirez et remplacez)
Code de correction
17454002 0.42 NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when
performing the below procedure.
- 2025-03-10: Updated post-replacement routine.
- 2024-01-17: Added step for ODIN routine to be run for vehicles running certain firmware versions.
- 2023-11-20: Updated security controller configuration steps.
- 2023-10-24: Updated post-replacement Toolbox routines.
- 2023-07-21: Added Note about security-related toolbox actions.
- 2023-10-26: Added some missing tool information.
- 2024-07-17: Updated the way of performing the routines from using Toolbox to using the touchscreen.
Remarque
Certaines des actions de l'outil Toolbox inclues dans la présente procédure concernent la sécurité du véhicule et ne peuvent être effectués que par les employés de Tesla ou une tierce partie autorisée à effectuer des actions de Toolbox relatives à la sécurité. Pour en savoir davantage, consultez la FAQ de l'abonnement au service disponible dans le menu déroulant du compte de l'utilisateur.
Caractéristiques techniques de couple
Description | Valeur de couple | Outils recommandés | Réutiliser/remplacer | Remarques |
---|---|---|---|---|
Vis qui fixent le module contrôleur de carrosserie de sécurité au panneau décoratif du porte-gobelet |
![]() 1.6 Nm (1.2 lbs-ft) |
|
Réutiliser | |
Vis (x4) qui fixent la bande lumineuse gauche de la console centrale à la console centrale |
![]() 1.6 Nm (1.2 lbs-ft) |
Réutiliser |
Retirer
-
Open all doors and lower all windows.
NoteLatch the rear doors with the doors open using a small flat blade screwdriver to prevent an accidental lockout.
- Move the driver seat and front passenger seat fully rearward and to the lowest position.
- Disconnect 12V power. See Alimentation 12 V/BT (déconnectez et connectez).
- Open the center console armrest fully.
- Remove the LH and RH center console decor trims. See Garniture décorative - console centrale - gauche (retirez et remplacez).
- Remove the screws and release the tabs that attach the LH bright strip to the center console, and then remove the strip from the console. Repeat this step to remove the RH bright strip.
- Release the clips (x6) that attach the cup holder decor panel to the cup holder assembly, and then separate the cup holder decor panel from the center console assembly.
- Disconnect the electrical connector from the security body controller module, and then remove the cup holder decor panel from the vehicle.
-
Remove the screws (x2) that attach the security body controller module to the cup holder decor panel, and then remove the security body controller module from the panel.
TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Clé à rochet/Clé dynamométrique
- TorqueVario Wiha-S 0,80Nm - 2,0Nm
- Wiha, adaptateur d'embout ¼ po
Installer
-
Install the screws (x2) that attach the security body controller module to the cup holder decor panel.1.6 Nm (1.2 lbs-ft)TIpNous recommandons l’utilisation des outils suivants :
- Douille Torx T20
- Clé à rochet/Clé dynamométrique
- TorqueVario Wiha-S 0,80Nm - 2,0Nm
- Wiha, adaptateur d'embout ¼ po
- Connect the electrical connector to the security body controller module.
- Attach the clips (x6) that attach the cup holder decor panel to the center console assembly.
- Install the RH bright strips: Start with the corner nearest to the IP carrier, and then continue towards the rear. Repeat this step on the LH bright strip.
-
Install the screws (x7) that attach the RH bright strip to the center console assembly. Repeat this step on the LH bright strip.1.6 Nm (1.2 lbs-ft)
- Install the RH center console decor trim, and then repeat this step on the LH center console decor trim. See Garniture décorative - console centrale - gauche (retirez et remplacez).
- Close the center console armrest.
- Reconnect 12V power. See Alimentation 12 V/BT (déconnectez et connectez).
- Restore the driver seat and front passenger seat back to their original position.
- Reinstall the vehicle firmware. See Réinstallation du logiciel – Écran tactile.
- Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : PROC_VCSEC_X_POST-REPLACEMENT-PROCEDUREvia Toolbox: (link)via Service Mode: Low Voltage ➜ Keys ➜ VCSEC Post Replacementvia Service Mode Plus: LowVoltage ➜ VCSEC Post Replacement ➜ VCSEC Post Replacement Procedure
- Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : PROC_VCSEC_C_PAIR-NFC-CARD-V2via Toolbox: (link)via Service Mode: Low Voltage ➜ Keys ➜ Pair Key
- Place the NFC card(s) on the NFC card reader in the center console, and check the function of the programmed NFC keys.
- Exit Service Mode. See Mode Entretien.
- Raise all windows and close all doors.
- Inform the customer that the new security body controller will not recognize any previously paired phone key. The customer must delete and re-pair their phone key to the vehicle, if they were previously using this feature. Instructions are available in the Owners Manual, and at the DIY web pages.