Code de correction NEW REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

1. Raise and support vehicle
   Remarque

   If vehicle has air suspension set to Jack Mode", Align lift adapter pins with lift point holes on body, Ensure vehicle is not charging, Remove charging cable if it's plugged in
2. Ouvrez le coffre avant électrique.
3. Ouvrez le hayon.
4. Remove the tonneau slats. See Slat System - Tonneau (Remove and Install).
5. Débranchez l’alimentation MT. Voir Mid-Voltage Power (Disconnect and Connect) (Modify),
6. Perform vehicle HV disablement procedure. See Vehicle HV Disablement Procedure (Test/Adjust).
7. Secure RDU header connector to ancillary
   Remarque

   1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

   

   

8. Remove pyro fuse access cover
   Remarque

   4x bolts, E-Torx 5 lobe, 10 Nm

   

9. Remove primary pyro fuse
   Remarque

   2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

   

   

10. Remove secondary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

11. Install pyro fuse access cover
    Remarque

    4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, If HV pack is being shipped then pyro fuses must be removed

    

    

12. Remove leather over gloves and HV insulating gloves
13. Lower vehicle until tires are touching the ground
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
14. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
15. Disconnect ancillary bay MV connector
    Remarque

    1x connector, Double locking, Release tab then pivot lever, Release second tab to disengage connector, Wait 1 second between locking tab release to discharge and prevent arcing

    

    

    

    

    

16. Put on HV insulating gloves and leather over gloves

    

17. Remove bolt securing busbar HV connector lid
    Remarque

    1x bolt, EP10, 9 Nm

    

18. Remove bolts securing HV connector to DC FC header
    Remarque

    2x bolts, 10mm, 9 Nm

    

19. Release HV connector from DC FC header
    Remarque

    1x connector, Use inflatable airbag if needed to suspend busbar assembly above ancillary assembly

    

20. Support HV Busbar assembly
    Remarque

    1X Bungee, Suspend assembly to maintain clearance, wrap bungee around busbar assembly to achieve required cord length, Connect bungee to tie down hook on bed side

    

    

21. Remove fast charger header doubler
    Remarque

    2x bolts, E10 5 Lobe Torx, 10 Nm

    

    

22. Remove mid voltage header bolts
    Remarque

    2x bolts, EP10, 6 Nm

    

23. Release fasteners securing ancillary bay cover to HV battery
    Remarque

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

24. Remove ancillary bay cover
    Remarque

    Install vacuum cup to ancillary bay cover surface, Lift and maneuver cover around busbar and tonneau cage to remove

    

    

    

25. Remove bolts securing PCS fuse
    Remarque

    2x bolts, 8mm, 6 Nm

    

    

26. Remove PCS fuse

    

    

27. Install HV compressor fuse
    Remarque

    Verify fuse is in the correct orientation

    

    

    

    

28. Install bolts securing HV compressor fuse
    Remarque

    2x bolts, 8mm, 6 Nm

    

29. Perform Hioki measurement from PCS fuse joint to FCC harness terminal
    Remarque

    1x HV joint, 200μΩ or less, Perform zero adjust to Hioki meter prior to testing

    

    

30. Perform Hioki measurement from PCS fuse joint to PCS harness terminal
    Remarque

    1x HV joint, 200μΩ or less, Perform zero adjust to Hioki meter prior to testing

    

    

    

31. Install ancillary cover
    Remarque

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

    

32. Secure ancillary cover fasteners to HV battery
    Remarque

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

33. Install mid voltage header bolts
    Remarque

    2x bolts, EP10, 6 Nm

    

34. Install fast charger header doubler
    Remarque

    2x bolts, E10 5 Lobe Torx, 10Nm

    

    

35. Clean HV connector contact surface of residual Penetrox
    Remarque

    Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector

    

36. Clean busbar HV connector contact surface of residual Penetrox
    Remarque

    Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

    

37. Apply Penetrox onto HV connector joints
    Remarque

    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

    

38. Position busbar connector and lower onto HV header
    Remarque

    Release bungee cord

    

39. Install bolts securing charge port busbar kit to HV Header
    Remarque

    2x bolts, 10mm, 9 Nm

    

40. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
    Remarque

    2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

41. Install bolt securing busbar HV connector lid
    Remarque

    1x bolt, EP10, 9 Nm

    

42. Connect ancillary bay MV connector
    Remarque

    1x connector, double locking, Rotate lever into 2nd lock, Perform a pull test to ensure connector engaged correctly

    

    

    

    

    

43. Raise vehicle fully and lower lift onto locks
    Remarque

    Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
44. Remove pyro fuse access cover
    Remarque

    4x bolts, E-Torx 5 lobe, 10 Nm

    

45. Clean pyro fuse mating surfaces
    Remarque

    Using an insulated tool wipe all four busbar mating surfaces within pyro fuse bay, Wipe top and bottom mating surfaces of each pyro fuse, Ensure no debris is present on any mating surface, Process shown with device cluster removed for clarity and safety, HV gloves and associated PPE must be worn at all times when cleaning mating surfaces, Allow 1 minute for IPA to dry

    

    

    

46. Install secondary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts, Bolts may be reused

    

    

47. Install primary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts, Bolts may be reused

    

    

48. Perform Hioki resistance test at each HV joint from HV busbar lead to pyro fuse busbar
    Remarque

    4x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

49. Install pyro fuse access cover
    Remarque

    4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, If HV pack is being shipped then pyro fuses must be removed

    

    

50. Remove leather over gloves and HV insulating gloves
51. Install the rear skid plate. See Skid Plate - Rear (Remove and Install).
52. Lower vehicle fully
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
53. Branchez l'alimentation électrique MT. Voir Mid-Voltage Power (Disconnect and Connect) (Modify),
54. Installez le tablier sous le capot. Voir Underhood Apron - Rear (Remove and Install),
55. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
56. Install the tonneau slats. See Slat System - Tonneau (Remove and Install).
57. Retirez le véhicule du pont élévateur. Voir Soulever le véhicule - pont élévateur à 2 poteaux,