10/12/2024 07:00:13

Tonneau Slat Assembly - Slat System - Tonneau (Rework)

Code de correction 1120122007 FRT 1.20 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 2024-11-26: Corrected note that still referenced adding 2 slats.
  • 2024-10-7: Updated steps to only add 1 slat instead of 2 slats.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Procédure

  1. Fermez le couvre-caisse.
  2. Inspect Water Management slat.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If any gap is present in the fore/aft space between the tonneau applique and Water Management slat, continue the rework to add 1 slat to close the gap.
  3. Remove the tonneau slat assembly. See Slat System - Tonneau (Remove and Install).
  4. Remove the crosscar fixation tubes (x3).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The last tube at the water management slat will be removed at a later step.
  5. Insert 2 inflatable bags under the tonneau slats at the tonneau transfer frame crossbar.
  6. Remove the LH Water Management slat bolts, rollers, and Tonneau Service Kit. Repeat this step for the RH side.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x slat bolts, 2x sleeves, 4x rollers, 1x Y-React Clip. Carefully pull outwards to release slat bolts from slats.
    Figure 1. LH shown; RH similar
    Figure 2. LH shown; RH similar
  7. Slide the Water Management slat away from the slat assembly to release it, and then remove the Water Management slat from the assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The chain links will come with the slat.
  8. Remove last link of LH chain. Repeat this step for the RH chain.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bushing. Use special tonneau removal tool to release roller bolt from the chain bushing. Remove the bushing and last chain slat. Discard bushing and use new bushing to lock pin in place. Remove Y-reaction clip and install at a later step at the Water Management Slat.
  9. Re-position Y-reaction clips on LH side of chain. Repeat this step for the RH side of the chain.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips. Replace any broken clips. Move all clips 1/2 step down to secure last link of chain. Leave top most link open to secure at a later step.
  10. Install one slat onto the front of the tonneau slat assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Apply silicon lubrication onto tonneau sealing slat to ease installation. Position mid slat onto tonneau and slide into place. Ensure slat is properly installed onto tonneau sealing channel.
  11. Install Water Management slat with tonneau chain
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Apply silicon lubrication onto tonneau sealing slat to ease installation, Position bushing slat to match slat hinge opening, Slide into place
  12. Install RH Mid Slat Roller Tonneau Service Kit to join new slat. Repeat this step for the LH side.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x slat bolts, 2x sleeves, 4x rollers, 1x Y-React Clips. Insert slat bolts into slats until fully engaged.
  13. Install LH Y-reaction clip to Water Management Slat Bolt Roller. Repeat this step for the RH side.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x Y-React Clip. Re-use clip removed from last link of chain at previous step. Ensure clip is fully engaged to both roller pins.
  14. Install fixation tubes
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x crosscar fixation tubes, From the Water Management crosscar fixation tube Skip 3 chain bushings for backlite opening when tonneau is closed, Skip 2 chain bushings for next tube then Skip1 chain bushing and install the last tube in the last bushing on the chain
  15. Install the tonneau slat assembly. See Slat System - Tonneau (Remove and Install).
  16. On the vehicle touchscreen, navigate to UI > Closures > Tonneau > Calibrate Tonneau to run the Tonneau Calibration routine.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Allow the routine to complete. The tonneau will move while the routine running.
  17. Fermez le couvre-caisse.
  18. Confirm there is no gap present between the tonneau cover and the tonneau applique.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Confirm no gap present fore/aft and top of slat to bottom of seal.
  19. Quitter mode Entretien. Voir Mode Entretien.
  20. Remontez la glace avant gauche et fermez la porte avant gauche.