16/07/2024 11:51:18

Hinges - Hood Strut (Remove and Install)

Code de correction 1133071071 1133071072 0.24 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Retirer

  1. Ouvrez la porte avant gauche et abaissez la vitre avant gauche.
  2. Set the air suspension to "Very High".
    Informational PurposesAn informational icon, calling your attention
    Remarque
    On the vehicle touchscreen, touch Controls > Ride Height > Very High.
  3. Enable "Jack Mode" of the air suspension.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    On the vehicle touchscreen, touch Controls > Service > Jack Mode.
  4. Ouvrez le coffre avant électrique.
  5. Remove the LH front wheel liner. See .
  6. Support the hood.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Current hood prop does not work with the Cybertruck hood due to size of opening, Have an assistant hold the hood up while the hood strut is removed and installed.
  7. Release the spring clip that attaches the hood strut to the hinge.
  8. Disconnect the electrical connector, then release the locking clip that attaches the hood strut, and then remove the hood strut from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Pic à prise souple, embout à 90 degrés, 6 po

Installer

  1. Install the hood strut.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    x1 electrical connector, x1 spring clip
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Engage the locking tab.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure that the spring clip is engaged to the stud mount before securing.
  2. Secure the hood strut to the hinge.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    x1 spring clip
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure that the spring clip is engaged to the stud mount before securing.
  3. Install the LH front wheel liner. See .
  4. Fermez le coffre avant électrique.
  5. Remove the suspension from "Jack Mode" and set it to "Medium".
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Touch Controls > Service > Jack Mode.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Touch Controls > Ride Height > Medium
  6. Remontez la glace avant gauche et fermez la porte avant gauche.