2026-03-13

Damper Reinforcement Assembly - Bed (Long Range) (Remove and Install)

Code de correction 12150300401 12150300402 1.14 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
  • 2026-02-26: Released new procedure.
  1. Open tailgate
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Press button to release, Use manual release as necessary
  2. Remove fastener covers from bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x covers
  3. Remove bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
  4. Remove LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Remarque
    15x clips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip
  5. Remove LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    13x clips, Start from rear, Pull from the bottom downwards
  6. Remove LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle
  7. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  8. Remove RH sail applique
    Informational PurposesAn informational icon, calling your attention
    Remarque
    15x clips
  9. Remove RH upper bed side wall assembly
    13x clips, Pull downwards
  10. Remove RH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 1x tab, Release RH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off in order to remove bed closeout panel from vehicle
  11. Remove RH bed side wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  12. Remove Damper Bed Reinforcement Assembly
  13. Install Damper Bed Reinforcement Assembly
  14. Install RH bed side wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  15. Install RH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 1x tab, Release RH tailgate cable to install bed closeout panel from vehicle
  16. Install RH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    13x clips, Replace any missing or damaged clips
  17. Install RH sail applique
    Informational PurposesAn informational icon, calling your attention
    Remarque
    13x clips, Replace any damaged clips
  18. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  19. Install LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 1x tab, Secure LH tailgate cable once closeout installed
  20. Install LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    13x clips, Replace any missing or damaged clips, Lift tonneau seal as required
  21. Install LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Remarque
    15x clips, 1x connector, 1x harness clip, Replace any broken clips
  22. Install bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
  23. Install fastener covers onto bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x covers
  24. Close tailgate