11/10/2024 02:03:48

Rear Bumper Fascia - Rear Fascia (Remove and Replace)

Code de correction 1001089052 0.84 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les composants électroniques du Cybertruck sont alimentés par une architecture  moyenne tension » ou « MT » de 48 V conçue pour améliorer l'efficacité. L'entretien des composants MT nécessite des connaissances et des soins supplémentaires afin d'éviter tout dommage corporel ou au véhicule. Lisez et comprenez les précautions relatives à la MT dans Précautions en électricité et assurez-vous que tous les cours de formation requis liés à la MT ont été suivis, le cas échéant.

Retirer

  1. Remove the rear fascia assembly. See Rear Bumper Fascia - Rear Fascia (Remove and Install).
  2. Remove the rear diffuser. See Undertray - Diffuser (Remove and Install).
  3. Remove the rear fascia harness. See Rear Fascia and Tail Gate Harnesses - Harness - Rear Fascia (Remove and Replace).
  4. Release the clips (x2) that attach the LH rear reflector to the rear fascia assembly, disconnect the electrical connector, and then remove the LH rear reflector from the assembly. Repeat this step for the RH rear reflector.
    Figure 1. LH shown; RH similar
  5. Remove the bolts (x3) that attach the LH reverse light to the rear fascia assembly, disconnect the reverse light electrical connector, and then remove the light from the assembly. Repeat this step for the RH reverse light.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
    Figure 2. LH shown; RH similar
    Figure 3. LH shown; RH similar
  6. Remove the trailer hitch cover. See Rear Bumper Fascia - Trailer Hitch Cover (Remove and Install).

Installer

  1. Place the rear fascia on a stable work stand.
  2. Install the trailer hitch cover. See Rear Bumper Fascia - Trailer Hitch Cover (Remove and Install).
  3. Position the LH reverse light into the rear fascia assembly, connect the electrical connector, and then install the bolts (x3) that attach the light to the assembly. Repeat this step for the RH reverse light.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
    Figure 4. LH shown; RH similar
    Figure 5. LH shown; RH similar
  4. Position the LH rear reflector onto the rear fascia assembly, connect the electrical connector, and then secure the clips (x2) that attach the LH rear reflector to the assembly. Repeat this step for the RH rear reflector.
    Figure 6. LH shown; RH similar
  5. Install the rear fascia harness. See Rear Fascia and Tail Gate Harnesses - Harness - Rear Fascia (Remove and Replace).
  6. Install the rear diffuser. See Undertray - Diffuser (Remove and Install).
  7. Install the rear fascia assembly. See Rear Bumper Fascia - Rear Fascia (Remove and Install).