19/01/2025 21:24:21

2nd Row Seat Covers and Pads - 2nd Row Seat Buckle Closeout Split - RH (Remove and Replace)

Code de correction NA REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les composants électroniques du Cybertruck sont alimentés par une architecture  moyenne tension » ou « MT » de 48 V conçue pour améliorer l'efficacité. L'entretien des composants MT nécessite des connaissances et des soins supplémentaires afin d'éviter tout dommage corporel ou au véhicule. Lisez et comprenez les précautions relatives à la MT dans Précautions en électricité et assurez-vous que tous les cours de formation requis liés à la MT ont été suivis, le cas échéant.
  1. Ouvrez la porte avant gauche et abaissez la vitre arrière gauche.
  2. Ouvrez la porte arrière droite et abaissez la vitre arrière droite.
  3. Retirez le tablier arrière sous le capot. Voir Underhood Trim - Rear Apron Assembly (Remove and Install).
  4. Débranchez l'alimentation électrique MT. Voir Disconnect MV Power.
  5. Remove the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  6. Fold down 2nd row 40 seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull tether to release then pivot down until locked in place
  7. Remove 2nd row RH outboard seatback bolster
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs, 1x datum, 3x clips, Release tab near the bottom of RH outboard bolster, Partially release RH 2nd row shoulder cover and remove bolster from vehicle
  8. Remove 2nd row RH inboard seatback bolster
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, 2x datums
  9. Remove clip securing RH 2nd row seat outboard B cover assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Position aside for access to clip
  10. Remove RH 2nd row seat back assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, 1x connector, 3x bolts, 10mm, 9 Nm, Pull upwards then away from frame then disconnect electrical harness, Release locking tab
  11. Remove 2nd row 40 seat cushion outboard cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Pull outward from lower forward section to release
  12. Release 2nd row 40 seat seat cushion from underbelly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull plastic retainers outward to release from underbelly
  13. Remove 2nd row seat cushion underbelly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Pull outwards from bottom to release
  14. Disconnect 2nd row seat cushion connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, 2x connectors, Release bracket from seat frame then disconnect connectors
  15. Remove 2nd row seat cushion assembly from frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Pull back seat cushion trim to access side clips, Slide seat cushion assembly upwards to remove from frame
  16. Remove RH 2nd row seat buckle split closeout assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 1x datum
  17. Remove RH 2nd row seat buckle split closeout assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 1x datum
  18. Position 2nd row seat cushion assembly onto frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Slide seat cushion assembly downwards onto frame, Pull back seat cushion trim to access side clips
  19. Connect 2nd row seat cushion connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, 2x connectors, Secure connectors then secure bracket to seat frame
  20. Install 2nd row seat cushion underbelly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Push inwards firmly to secure
  21. Secure 2nd row 40 seat seat cushion to underbelly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push plastic retainers into grooves, Manipulate material as required to engage all retainers
  22. Install 2nd row 40 seat cushion outboard cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Push inwards at bottom to secure
  23. Install RH 2nd row seat back assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, 1x connector, 3x bolts, 10mm, 9 Nm, Connect electrical harness before fully seating assembly, Engage locking tab
  24. Install clip securing RH 2nd row seat outboard B cover assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Ensure strap is not twisted
  25. Install 2nd row RH inboard seatback bolster
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, 2x datumns
  26. Install 2nd row seatback RH outboard bolster
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs, 1x datum, 3x clips, Position LH outboard bolster into place, Ensure all clips and tabs are fully engaged, Replace any missing or damaged clips, Secure LH 2nd row shoulder cover, Perform push-pull-push test datums
  27. Install the rear wall lower trim. See Passenger Compartment Carpet - End Item, Rear Wall Lower Trim, Soft Trim (Remove and Install).
  28. Rebranchez l’alimentation MT. Voir Disconnect MV Power.
  29. Installez le tablier arrière sous le capot. Voir Underhood Trim - Rear Apron Assembly (Remove and Install).
  30. Raise the rear windows and close the rear doors.