2025-09-11

Harness - Seat - 1st Row - RH (Remove and Replace)

Code de correction 1710091012 1710091011 0.84 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les composants électroniques du Cybertruck sont alimentés par une architecture  moyenne tension » ou « MT » de 48 V conçue pour améliorer l'efficacité. L'entretien des composants MT nécessite des connaissances et des soins supplémentaires afin d'éviter tout dommage corporel ou au véhicule. Lisez et comprenez les précautions relatives à la MT dans Précautions en électricité et assurez-vous que tous les cours de formation requis liés à la MT ont été suivis, le cas échéant.
  • 2025-08-07: Released new procedure.
  1. Remove the RH 1st row seat assembly from the vehicle, and then place the seat on a protected surface. See Seat Assembly - 1st Row - RH (Remove and Install).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommended assistance. Position so that the underside of the seat is accessible.
  2. Remove the RH 1st row seat outboard side shield. See Side Shield - Outboard - 1st Row Seat - LH (Remove and Install).
  3. Remove RH front seat outboard side shield carrier
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 2x tabs, Release leading edge of trim and slide away from seat frame
  4. Remove the RH 1st row seat inboard side shield. See Side Shield - Inboard - 1st Row Seat - LH (Remove and Install).
  5. Disconnect RH front seat buckle harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  6. Remove RH front seat inboard side shield carrier
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 1x datums, Release leading edge of trim and slide away from seat frame
  7. Release seat back elastic straps from seat frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x straps
  8. Unzip RH front seatback trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x zippers, Pull tails of zippers outside seatback then unzip, Use of a straight pick can aid in moving zipper pulls
  9. Fold RH front seat back trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, Fold material upward
  10. Disconnect RH front seat harness connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    13x connectors
  11. Remove RH front seat harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    15x clips
  12. Install RH front seat harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    15x clips
  13. Connect RH front seat harness connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    14x connectors
  14. Unfold RH front seat back trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips,
  15. Zip RH front seatback trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x zippers, Zip each side of seatback trim then tuck in tails, Use of a straight pick can aid in moving zipper pulls
  16. Install seat back elastic straps onto seat frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x straps
  17. Install the RH 1st row seat inboard side shield carrier
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 2x tabs, Position leading edge of trim and slide into seat frame
  18. Install the RH 1st row seat inboard side shield. See Side Shield - Inboard - 1st Row Seat - LH (Remove and Install).
  19. Connect RH front seat buckle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  20. Install RH side shield carrier onto RH front seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 2x tabs, Slide forward onto seat frame aligning clips and tabs
  21. Install the RH 1st row seat outboard side shield. See Side Shield - Outboard - 1st Row Seat - LH (Remove and Install).
  22. Install the RH 1st row seat assembly. See Seat Assembly - 1st Row - RH (Remove and Install).