10/12/2024 07:00:12

Mud Flaps (Retrofit)

Code de correction 12207006 0.24 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Réajuster

  1. Open the LH front door and lower the LH front window.
  2. Turn the steering wheel fully to the left to provide access to the working areas.
  3. Remove the clips (x2) that partially attach the LH front wheel arch liner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Outil de levier avec pince
    Figure 1. LH shown; RH similar
  4. Position the LH front mud flap on the vehicle, and then install the clips (x2) that attach the mud flap to the LH front wheel arch liner.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Install the clips starting from right to left.
    Figure 2. LH shown; RH similar
    Figure 3. LH shown; RH similar
  5. Install the bolts (x2) that attach the LH front mud flap to the LH rocker panel.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Align the bolts with the rocker panel holes.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Rallonge de 2 po
    • Douille longue de 10 mm
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé dynamométrique avec mesure angulaire
    Figure 4. LH shown; RH similar
  6. Remove the clips (x3) that partially attach the RH rear wheel arch liner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Outil de levier avec pince
    Figure 5. RH shown; LH similar
  7. Remove the bolt that partially attaches the RH rear diffuser to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Rallonge de 2 po
    • Clé à cliquet sans fil/Visseuse à percussion
    • Douille Torx T30
    Figure 6. RH shown; LH similar
  8. Move the RH rear wheel arch liner away from the working area as required, and then install the U-nuts (x3) onto the RH rear fascia.
    Figure 7. RH shown; LH similar
  9. Move the RH rear wheel arch liner back to original position.
    Figure 8. RH shown; LH similar
  10. Position the RH rear mud flap on the vehicle, and then install the bolts (x3) that attach the mud flap to the RH rear wheel arch liner.
    2.2 Nm (1.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille longue de 10 mm
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé dynamométrique avec mesure angulaire
    Figure 9. RH shown; LH similar
    Figure 10. RH shown; LH similar
  11. Install the bolt that attaches the RH rear mud flap to the RH rear diffuser.
    2.2 Nm (1.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille longue de 10 mm
    • Clé à cliquet sans fil/Visseuse à percussion
    • Clé dynamométrique avec mesure angulaire
    Figure 11. RH shown; LH similar
  12. Turn the steering wheel fully to the right to provide access to the working areas.
  13. Repeat step 3 through step 5 for the RH front mud flap.
  14. Repeat step 6 through step 11 for the LH rear mud flap.
  15. Raise the LH front window and close the LH front door.