2026-07-31

Coax Cable - Side Repeater - Front - RH (Overlay) (Remove and Replace)

Code de correction 17403112 FRT 1.86 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les composants électroniques du Cybertruck sont alimentés par une architecture  moyenne tension » ou « MT » de 48 V conçue pour améliorer l'efficacité. L'entretien des composants MT nécessite des connaissances et des soins supplémentaires afin d'éviter tout dommage corporel ou au véhicule. Lisez et comprenez les précautions relatives à la MT dans Précautions en électricité et assurez-vous que tous les cours de formation requis liés à la MT ont été suivis, le cas échéant.
  • 2025-10-06: Released new procedure.

Overlay

  1. Open LH front door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push LH B-pillar door trigger to release
  2. Lower LH front window
  3. Open RH front door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push RH B-pillar door trigger to release
  4. Lower RH front window
  5. Remove LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip
  6. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 3x datums, 2x tabs, Release sill plate, Pull rearward then upward
  7. Remove footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 3x magnets, 1x bolt, 10mm, 3 Nm, Bolt is captive to tether
  8. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 3x tabs, Release tabs then slightly bend live hinge and release clip
  9. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 3x datums, 2x tabs, Release sill plate, Pull rearward then upward
  10. Open powered front trunk
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via exterior switch or UI
  11. Exécutez la routine ODIN PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
  12. Set air suspension ride height to “High”
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via UI > Controls > Ride Height > High
  13. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify EPBs are engaged, Select charge port icon to ensure drive state is disengaged then power down vehicle via Controls > Safety > Power Off
  14. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  15. Disconnect first responder loop and MV battery connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules
  16. Remove Mid IP panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    19x clips
  17. Remove lower IP panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x patch bolts, 10mm, 7 Nm, 4x screws, T20, 2 Nm, 15x panel clips, 1x push clip, 4x connectors, Discard patch bolts after removal, Release LH/RH knee air bag harness from the main IP harness buddy clips, Remove blue tape to allow service slack & prevent stress to knee air bag connectors, Release connector locking tabs, Release OBD port from lower IP
  18. Remove RH EPP clip
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Pull back for access to car computer
  19. Fold back RH carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, 4x datums
  20. Disconnect glovebox USB connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release locking tab
  21. Remove RH front fender flare cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 3x datums, 1x connector, Release all clips then repeater connector before removal, Camera harness is very short, Ensure excess force is not exerted on harness
  22. Remove the megabeam. See Panneaux intérieurs avant – Megabeam (retirer et installer)
  23. Release RH front wheel liner from HV battery chinstrap
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 2x bolts, 10mm, 6 Nm
  24. Release RH front wheel liner push nuts
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x push nuts, Replace if damaged
  25. Remove RH front wheel liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Manipulate as required to clear fender flare and tire, Shown with wheel removed for clarity
  26. Support supermanifold with inflatable air bag
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Insert inflatable airbag between body and supermanifold
  27. Release RH grommet from body
  28. Remove electrical tape securing harness bundle to rubber dust boot
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot, Do not damage coax
  29. Apply harness tape onto RH coax overlay cable before installation
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  30. Position RH coax overlay cable into place, Place through RH wheel liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull till you have roughly 7 inches of cable towards the interior of the vehicle
  31. Pull RH coax overlay cable through RH frunk harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull harness towards car computer
  32. Pull RH coax overlay cable through bulkhead and into interior cabin
  33. Release side fender cameras connector X0858 from car computer
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release red tab before removing connector
  34. Remove locking pin from side fender cameras connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Carefully pry pin out of connector and fully remove locking pin
  35. Remove coax terminal 1 (RHS) cable from connector
  36. Insert new side repeater coax terminal 1 (RHS) cable onto side repeater cameras connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm
  37. Secure locking pin to connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Align tabs of lock in connector housing, Ensure flush installation of locking pin to connector housing
  38. Install side fender cameras connector X0858 onto car computer
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Secure red tab
  39. Position RH coax overlay cable onto RH frunk main harness, Secure cable onto harness using zip ties
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x zip-ties, Trim off excess material after harness has been secured
  40. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Cut the coax connector only
  41. Secure RH grommet onto body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use electrical tape to wrap the end of the dust boot
  42. Remove inflatable air bag from supermanidfold
  43. Position RH front wheel liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Manipulate as required to clear fender flare and tire, Shown with wheel and tire removed for clarity
  44. Install RH front wheel liner push nuts
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x push nuts, Install new push nuts
  45. Secure RH front wheel liner to HV battery chinstrap
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip, 2x bolts, 10mm, 6 Nm
  46. Install RH front fender flare cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 3x datums, 1x connector, Make camera connection before flare installation, Ensure excess force is not exerted on camera harness, Replace any missing or damaged clips
  47. Install the megabeam. See Panneaux intérieurs avant – Megabeam (retirer et installer)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Stop once the frunk harness has been secured to the washer fluid reservoir.
  48. Connect glovebox USB connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage locking tab
  49. Unfold RH front cabin carpet into position
  50. Instal RH EPP clip
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  51. Install lower IP panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x patch bolts, 10mm, 7 Nm, 4x screws, T20, 2 Nm, 15x panel clips, 1x push clip, 4x connectors, Install new patch bolts, Engage connector locking tabs, Install OBD connector, Secure LH & RH knee air bag harness service slack to buddy clips on main IP harness
  52. Install Mid IP panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    19x clips, Replace any missing or damaged clips
  53. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 3x datums, 2x tabs
  54. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 3x tabs, Replace any missing or damaged clips
  55. Install footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 3x magnets, 1x bolt, 10mm, 3 Nm, Bolt is captive to tether, Replace any missing or damaged clips or magnets
  56. Install LH Lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 3x datums, 2x tabs, Replace any missing or damaged clips
  57. Install LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 3x tabs, Replace any missing or damaged clips
  58. Install MV Battery
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 8 Nm, Slide rearwards into position
  59. Connect first responder loop and MV battery connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down
  60. Install frunk assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x bolts, 10mm, 12 Nm, 2x bolt caps, 2x bumpstops, 1x connector, Install bolt covers to frunk floor, Install washer fluid cap, Install bumpstops by aligning tabs then turning clockwise, Ensure emergency frunk release functions
  61. Close powered front trunk
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via exterior switch or UI
  62. Raise LH front window
  63. Unlock vehicle gateway
    Informational PurposesAn informational icon, calling your attention
    Remarque
    After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information
  64. Clear camera calibration via Service UI
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via UI > Driver Assist > Cameras > Clear Camera Calibration > Camera Input > ForwardFacing > Run
  65. Connect to vehicle using Toolbox 3
    Informational PurposesAn informational icon, calling your attention
    Remarque
    OBD-II connection is integrated into drivers lower IP cover, Open Toolbox 3 website and establish connection to vehicle, https://toolbox.teslamotors.com, Select connection status icon at top right corner then select connect locally, Icon will turn green when connected, Successful connection will automatically unlock vehicle gateway and place UI in Service Mode Plus
  66. Exécutez la routine ODIN PROC_DAS_X_ENTER-CALIBRATION-MODEvia Toolbox:(link)
  67. Select PING-HTTP_DAS_L_REPEATER-CAMERA-SCRIPT, and Run Routine
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Choose the routine that has the 'Script' at the end of the name, Change timeout to 100, Click run
  68. Disconnect Toolbox 3 from vehicle and remove laptop
  69. Exécutez la routine ODIN PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  70. Close LH front door