2026-07-02

Seat Assembly - 2nd Row (Remove and Replace)

Code de correction 13050401201 13050401202 FRT 1.74 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les composants électroniques du Cybertruck sont alimentés par une architecture  moyenne tension » ou « MT » de 48 V conçue pour améliorer l'efficacité. L'entretien des composants MT nécessite des connaissances et des soins supplémentaires afin d'éviter tout dommage corporel ou au véhicule. Lisez et comprenez les précautions relatives à la MT dans Précautions en électricité et assurez-vous que tous les cours de formation requis liés à la MT ont été suivis, le cas échéant.
  • 2026-06-12: Released new procedure.

Retirer

  1. Open all four doors
  2. Lower all four windows
  3. Manually latch all doors to prevent lockout
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Engage latch with screwdriver
  4. Enter Service Mode. See Mode Entretien.
  5. Raise and move LH front seat forward
  6. Move RH front seat forward
  7. Disconnect MV power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  8. Close LH and RH visors and retract LH and RH windshield shade assemblies
  9. Remove the LH and RH 2nd row seatback shoulder covers. See Shoulder Cover - LH - 2nd Row Seat (Remove and Install).
  10. Remove the rear vehicle controller. See Body Controller - Rear (Remove and Install).
  11. Release all connections from charge port ecu
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors
  12. Remove charge port ECU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolts, 10 mm, 5 Nm, 2x tabs
  13. Release 2nd row center retractor from 2nd LH row buckle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push red release mechanism to release retractor
  14. Remove bolts securing 2nd row seat back onto the back wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, 10mm, 9 Nm, 2x bolts, 10mm, 7 Nm
  15. Remove bolts securing lower 2nd row full seat assembly onto the back wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x bolts, 15mm, 50 Nm
  16. Remove bolts securing LH and center/RH 2nd row buckle onto 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 15mm, 40 Nm
  17. Remove bolts securing 2nd row seat assembly onto vehicle structural frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, 15mm, 50 Nm
  18. Remove LH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 1x datum
  19. Release RH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 1x datum
  20. Release 2nd row center seat belt from 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x button
  21. Remove 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance

Installer

  1. Install 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Assistance recommended for safe installation onto frame
  2. Install 2nd row center seat belt onto 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x button
  3. Install RH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 1x datum
  4. Install LH 2nd row shoulder cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, 1x datum
  5. Install bolts securing 2nd row seat assembly onto vehicle structural frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, 15mm, 50 Nm
  6. Install the rear vehicle controller. See Body Controller - Rear (Remove and Install).
  7. Install bolts securing LH and center/RH 2nd row buckle onto 2nd row seat assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 15mm, 40 Nm
  8. Install bolts securing lower 2nd row full seat assembly onto the back wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x bolts, 15mm, 50 Nm
  9. Install bolts securing 2nd row seat back assembly onto the back wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x bolts, 10mm, 9 Nm, 2x bolts, 10mm, 7 Nm
  10. Secure 2nd row center retractor onto 2nd LH row buckle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push red release mechanism to release retractor
  11. Install charge port ECU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10 mm, 5 Nm, 2x tabs, Align charge port ecu into cavity for installation
  12. Secure all connections to charge port ecu connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors
  13. Reinstall all components that were removed for access. See Shoulder Cover - LH - 2nd Row Seat (Remove and Install).
  14. Connect mid-voltage power. See Mid-Voltage Power (Disconnect and Connect) (Modify).
  15. Move RH front seat to original position
  16. Lower and move LH front seat to original position
  17. Exit Service Mode. See Mode Entretien.
  18. Raise all four windows.
  19. Close all four doors.