Code de correction NEW REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

1. Raise and support vehicle
   Remarque

   Set air suspension to "Jack Mode"

   

   

2. Open powered front trunk
   Remarque

   Via exterior switch or UI

   

   

3. Open tailgate
   Remarque

   Press button to release

   

4. Power down vehicle via UI
   Remarque

   Verify EPBs are engaged, Select charge port icon to ensure drive state is disengaged then power down vehicle via Controls > Safety > Power Off

   

5. Remove rear underhood apron
   Remarque

   9x clips

   

   

6. Disconnect FRL connector then disconnect MV battery connector
   Remarque

   2x connectors, Release locking tab then disconnect FRL connector, Slide eCPA to left then lift lever to release MV battery connector, Early production trucks may have black FRL connector, Release eCPA by pushing down to unlock and slide red locking tab, Wait 2 minutes for electrical circuits to discharge before disconnecting modules

   

   

   

7. Verify operation of multimeter
   Remarque

   Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals

   

   

8. Raise vehicle fully
   Remarque

   Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting

   

   

9. Remove rear skid plate
   Remarque

   6x clips, 3x bolts, 15mm, 42 Nm, 5x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm

   

   

   

   

   

10. Remove all items from pockets and ensure not wearing metal items

    

11. Inspect HV insulating gloves
    Remarque

    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves.

    

12. Put on HV insulating gloves and leather over gloves

    

13. Verify no HV - Install amp clamp to RDU HV harness
    Remarque

    Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as requiredIf current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.Release locking tab and rotate the release lever up to disengage the connector, Release harness clip, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damagedMake sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

    

    

14. Secure RDU header connector to ancillary
    Remarque

    1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

    

    

15. Remove pyro fuse access cover
    Remarque

    4x bolts, E-Torx 5 lobe, 10 Nm

    

16. Remove primary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

17. Remove secondary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

18. Remove leather over gloves and HV insulating gloves
19. Lower vehicle until tires are touching the ground
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

20. Disconnect ancillary bay MV connector
    Remarque

    1x connector, Double locking, Release tab then pivot lever, Release second tab to disengage connector, Wait 1 second between locking tab release to discharge and prevent arcing

    

    

    

    

    

21. Remove bolt securing busbar HV connector lid
    Remarque

    1x bolt, EP10, 9 Nm

    

22. Remove bolts securing HV connector to DC FC header
    Remarque

    2x bolts, 10mm, 9 Nm

    

23. Release HV connector from DC FC header
    Remarque

    1x connector, Use inflatable airbag to suspend busbar assembly above ancillary assembly

    

24. Support HV Busbar assembly
    Remarque

    Suspend assembly to maintain clearance

    

25. Remove fast charger header doubler
    Remarque

    2x bolts, E10 5 Lobe Torx, 10 Nm

    

    

26. Release low voltage header
    Remarque

    2x bolts, EP10, 6 Nm

    

27. Release fasteners securing ancillary cover to HV battery
    Remarque

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

28. Remove ancillary cover
    Remarque

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

29. Inspect HV insulating gloves
    Remarque

    Check gloves for damage prior to use, Refer to service document TN-15-92-003

    

30. Put on HV insulating gloves and leather over gloves

    

31. Disconnect PCS MV connector
    Remarque

    1x connector, 1x zip tie, Slide red lock off of lever, Rotate lever to release connector, Remove zip tie as needed

    

    

32. Release PCS MV harness
    Remarque

    1x bolt, EP10, 6 Nm, 2x clips, Move aside as needed

    

33. Release MV header
    Remarque

    4x datums, 1x edge clip, 1x fir tree clip

    

    

    

34. Release HVC connectors
    Remarque

    2x clips, 3x connectors, Release connector locks, Depress levers and pull at connector, Do not pull from harnessIf RTV is present at 2 connectors, using a ceramic knife cut through and remove RTV until connector can be disconnected

    

    

    

    

    

35. Release BMB passthrough connectors
    Remarque

    2x connectors, Release connector locks, Depress levers and pull at connector, Do not pull from harness

    

    

    

36. Release ACJB LV connector & ACJB to device cluster HV connector
    Remarque

    2x clips, 2x connectors, Release connector locks, Depress levers and pull at connectors, Do not pull at harness

    

    

    

37. Remove MV ancillary harness

    

    

38. Poistion MV ancillary harness for install

    

    

39. Secure ACJB LV and HV connectors
    Remarque

    2x clips, 2x connectors, Secure connector locks

    

    

    

40. Secure BMB passthrough connectors
    Remarque

    2x connectors, Secure connector locks, Connectors are poke yoked do not force engagement, Ensure locking tabs are facing front of vehicle when connecting

    

    

    

41. Secure HVC connectors
    Remarque

    2x clips, 3x connectors, Release connector locks, Depress levers and pull at connector, Do not pull from harness, Apply sealant to connectors at device cluster if it was present during disassembly

    

    

    

    

    

42. Secure MV header
    Remarque

    4x datums, 1x edge clip, 1x fir tree clip

    

    

43. Secure PCS MV harness
    Remarque

    1x bolt, EP10, 6 Nm, 2x clips

    

44. Connect PCS MV connector
    Remarque

    1x connector, 1x zip tie, Install zip tie onto ECPA latch, PCS header not datumed, Ensure correct orientation and polarity of connection, Harness color red for LV+ and black for LV-, Swing down locking lever, Slide lock fully to engage on top of lever

    

    

    

    

45. Install ancillary cover
    Remarque

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

    

46. Remove leather over gloves and HV insulating gloves
47. Secure fasteners of cover to HV battery
    Remarque

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

48. Secure low voltage header
    Remarque

    2x bolts, EP10, 6 Nm

    

49. Secure fast charger header doubler
    Remarque

    2x bolts, E10 5 Lobe Torx, 10Nm

    

    

50. Clean HV connector contact surface of residual Penetrox
    Remarque

    Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector

    

51. Clean busbar HV connector contact surface of residual Penetrox
    Remarque

    Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

    

52. Apply Penetrox onto HV connector joints
    Remarque

    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

    

53. Position busbar connector and lower onto HV header
    Remarque

    Release bungee cord

    

54. Install bolts securing charge port busbar kit to HV Header
    Remarque

    2x bolts, 10mm, 9 Nm

    

55. Inspect HV insulating gloves
    Remarque

    Check gloves for damage prior to use, Refer to service document TN-15-92-003

    

56. Put on HV insulating gloves and leather over gloves

    

57. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
    Remarque

    2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

58. Remove leather over gloves and HV insulating gloves
59. Install bolt securing busbar HV connector lid
    Remarque

    1x bolt, EP10, 9 Nm

    

60. Connect Ancillary bay MV connector
    Remarque

    1x connector, double locking, Rotate lever into 2nd lock, Perform a pull test to ensure connector engaged correctly

    

    

    

    

    

61. Raise vehicle fully

    

62. Remove all items from pockets and ensure not wearing metal items
63. Inspect HV insulating gloves
    Remarque

    Check gloves for damage prior to use, Refer to service document TN-15-92-003

    

64. Put on HV insulating gloves and leather over gloves

    

65. Clean mating surface of the pyro
    Remarque

    Use a non-conductive plastic tool to clean the busbar side, Allow 1 minute for IPA to fully dry, Do not use any other types of cleaner

    

    

    

66. Install secondary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts

    

    

67. Install primary pyro fuse
    Remarque

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts

    

    

68. Perform Hioki resistance test at each HV joint from HV busbar lead to pyro fuse busbar
    Remarque

    4x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

69. Remove leather over gloves and HV insulating gloves
70. Install pyro fuse access cover
    Remarque

    4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, If HV pack is being shipped then pyro fuses must be removed

    

    

71. Install Mid-aero shield
    Remarque

    6x clips, 3x bolts, 15mm, 70 Nm, 3x bolts, 13mm, 28 Nm, 2x bolts, 10mm, 6 Nm

    

    

    

    

    

72. Lower vehicle until tires are touching the ground
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

73. Install bed floor assembly
    Remarque

    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance

    

    

    

    

    

74. Install fastener covers onto bed floor assembly
    Remarque

    14x covers

    

    

    

    

75. Close tailgate

    

76. Connect FRL connector then connect MV battery connector
    Remarque

    2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down

    

    

    

77. Install rear underhood apron
    Remarque

    9x clips, Adjust windshield seal as required

    

    

78. Close powered front trunk
    Remarque

    Via exterior switch or UI

    

79. Remove vehicle from lift
    Remarque

    Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"