2026-05-28

Bed Side Wall - LH (Standard) (Remove and Install)

Code de correction NEW REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
  • 2026-05-08: Released new procedure.
  1. Ouvrez le couvre-caisse.
  2. Ouvrez le hayon.
  3. Ouvrez la porte avant gauche et abaissez la glace avant gauche.
  4. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
  5. Remove the LH sail applique. See Sail Applique - RH (Remove and Install) (Post 11/4/2024).
  6. Remove the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install)
  7. Remove the upper bedside wall assembly. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
  8. Remove the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
  9. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 15mm, 46 Nm, 2x bolts, T45, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 3x connectorsRelease locking tabs, Disconnect bed outlet connectors from bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Release locking tabs, Slide lock to release.
  10. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 15mm, 46 Nm, 2x bolts, 13mm, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Secure locking tabs, Connect bed outlet connectors onto bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Secure locking tabs, Slide lock to secure, Recommend assistance
  11. Install the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
  12. Install the upper bedside wall assembly. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
  13. Install the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install)
  14. Install the LH sail applique. See Sail Applique - RH (Remove and Install) (Post 11/4/2024).
  15. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).