2025-09-23

Door - Rear - LH (Remove and Replace)

Code de correction 1010025042 1010025052 0.90 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

  • 2025-08-28: Linked door panel procedure that includes door panel and door assembly rework steps.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Les composants électroniques du Cybertruck sont alimentés par une architecture  moyenne tension » ou « MT » de 48 V conçue pour améliorer l'efficacité. L'entretien des composants MT nécessite des connaissances et des soins supplémentaires afin d'éviter tout dommage corporel ou au véhicule. Lisez et comprenez les précautions relatives à la MT dans Précautions en électricité et assurez-vous que tous les cours de formation requis liés à la MT ont été suivis, le cas échéant.
  1. Open LH front door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push LH B-pillar door trigger to release
  2. Lower all 4 windows
  3. Open LH rear door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push LH C-pillar door trigger to release
  4. Remove LH rear beltline assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    16x clips, 2x datums, 2x connectors
  5. Remove LH rear door inner waist belt seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x rubber grommets, Release grommets from each end, Lift LH rear door inner waist belt seal upwards to remove from door assembly
  6. Remove LH rear door outer waist belt seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull outwards to remove LH rear door outer waist belt seal from door assembly
  7. Raise LH rear window
  8. Manually latch LH rear door
  9. Remove bolts securing LH rear door trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x bolts, 8mm, 4Nm
  10. Release LH rear door trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    15x clips, 2x connectors, Replace any broken clips
  11. Remove LH rear door grommets
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x grommets
  12. Remove LH rear door glass
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 4 Nm, Recommend assistance, Clamps do not hold whole base of regulator
  13. Retirez le tablier arrière situé sous le capot. Voir Underhood Apron - Rear (Remove and Install),
  14. Débranchez l’alimentation MT. Voir Disconnect MV Power (Modify),
  15. Release LH rear door harness from close out panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 4x connectors, Release locking tabs
  16. Remove LH rear door closeout panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x bolts, 8mm, 4 Nm, 2x bolts, 10mm, Torque?, 2x datums, Gently pry panel to release datums, Pull bottom portion outwards and lower assembly to allow clearance for regulator rails
  17. Partially remove LH rear door harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x grommet, 3x clips, Do not disconnect door harness to B-pillar connection, Position harness to the side
  18. Disconnect LH rear door latch harness connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release locking tab
  19. Disconnect LH rear door presenter harness connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release locking tab
  20. Remove LH rear closure device harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips 1x grommet
  21. Remove LH rear door latch
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x grommet, 3x bolts, T30, 13 Nm
  22. Remove LH rear door presenter
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, T30, 13 Nm
  23. Remove LH rear secondary seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    16x clips, Start from outer edge, Use trim pry tool to prevent clips from breaking inside door
  24. Remove LH rear door overslam bumper
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs
  25. Remove LH rear check strap and check strap close out
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T40, 23 Nm, 2x nuts, 10mm, 8.5 Nm, Remove rubber then nuts, Rotate device 90 degrees to remove
  26. Remove LH rear door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 15mm, 38 Nm, Recommend assistance
  27. Install LH rear door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 15mm, 38 Nm, Recommend assistance
  28. Install LH rear check strap and check strap close out
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T40, 23 Nm, 2x nuts, 10mm, 8.5 Nm, Rotate device 90 degrees to position, Slide device through rubber then install fasteners
  29. Install LH rear door overslam bumper
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs
  30. Install LH rear secondary seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    16x clips, Note that ONE pin is different color, that begins on the outer edge
  31. Install LH rear door presenter
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, T30, 13 Nm
  32. Install LH rear door latch
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x bolts, T30, 13 Nm, Use tab on emergency release to guide grommet
  33. Install LH rear closure device harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 1x grommet
  34. Connect LH rear door presenter harness connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Secure locking tab
  35. Connect LH rear door latch harness connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Push in locking tab
  36. Install LH rear door harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 1x grommet, 3x clips
  37. Install LH rear door closeout panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x bolts, 8mm, 4 Nm, 2x bolts,10mm, 12 Nm, 2x grommets
  38. Secure LH rear door harness onto close out panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 4x connectors
  39. Connect external window switch
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  40. Install LH rear door glass
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 4 Nm, Torque at later step, Make sure to properly secure onto regulator mount
  41. Install LH rear door outer waist belt seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Align LH rear door outer waist belt seal onto door assembly for installation, Ensure seal is properly seated onto door assembly
  42. Install LH rear door inner waist belt seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x rubber grommets, Ensure LH rear door inner waist belt seal is properly installed onto door assembly
  43. Manually unlatch LH rear door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull on the emergency cable to unlatch, If applicable
  44. Connect FRL connector then connect MV battery connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Connect FRL connector then secure locking tab, Position lever to secure MV battery connector then slide eCPA to right, Early production trucks may have black FRL connector, If power cycling vehicle then ensure at least 60 seconds has passed since powering down
  45. Close LH rear door
  46. Check and adjust gap and flushness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Connect external window switch to help with adjustment, Reference CVIS for specification
  47. Open LH rear door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push LH C-pillar door trigger to release
  48. Torque bolts securing LH rear window to regulator
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 13 Nm
  49. Install LH rear door grommets
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x grommets
  50. Disconnect external window switch
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  51. Install the LH front door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Follow steps to inspect and rework the door panel and/or the door assembly, if required.
  52. Raise all 4 windows
  53. Installez le tablier sous le capot. Voir Underhood Apron - Rear (Remove and Install),
  54. Close LH rear door
  55. Close LH front door
  56. Check LH rear door gap and flushness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify door alignment, If adjustment is needed then reference current CVIS specifications