11/10/2024 02:03:46

Device Cluster Assembly (Backup and Restore)

Code de correction NA REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Backup

  1. Ouvrez la porte avant gauche et abaissez la vitre avant gauche.
  2. Retirez le tablier arrière sous le capot. Voir Underhood Trim - Rear Apron Assembly (Remove and Install).
  3. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3.0 (connecter et déconnecter).
  4. On the vehicle touchscreen, navigate to Service UI > High Voltage Tab > Procedures > Device Cluster Assembly (DCA) Replacement > Backup Old DCA, and then tap Run to back up the device cluster assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Allow the routine to complete before continuing.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure the routine completes successfully.

Restore

  1. Débranchez l'alimentation électrique MT. Voir Disconnect MV Power.
  2. Connect the MV battery maintainer, but leave the MV battery disconnected: Attach the positive terminal to jump post, and then attach the negative terminal to the bolt located between the brake fluid reservoir and the front trunk.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x cover, Secure MV maintainer but leave the Li-ion battery disconnected, Secure positive terminal to jump post, Secure negative terminal to bolt located between brake fluid reservoir and front trunk, Connect maintainer to power supply, DO NOT allow positive cable to make contact with other metal components, Prevent shorting the cables,Do not have a MV maintainer and the Li-ion battery simultaneously connected for any extended period of time
  3. Connect the MV battery maintainer to power supply.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    DO NOT allow the positive cable to make contact with other metal components. Prevent shorting the cables.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Do not have the MV battery maintainer and the MV battery simultaneously connected for any extended period of time.
  4. Reestablish vehicle connection to Toolbox 3.
  5. On the vehicle touchscreen, navigate to Service UI > High Voltage Tab > Procedures > Device Cluster Assembly Replacement > Restore New DCA, and then tap Run to restore the device cluster assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Laptop must be connected via Toolbox 3 for duration of routine. Follow all on screen instructions and requirements. Do not disconnect Toolbox 3 until routine completes successfully.
  6. Power down the vehicle through the vehicle touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify EPBs are engaged. Touch the charge port icon to ensure the drive state is disengaged, and then power down vehicle via Controls > Safety > Power Off.
  7. Remove the MV battery maintainer from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Unplug the MV battery maintainer first from the power outlet, and then remove the positive and negative leads from the jump posts.
  8. Rebranchez l’alimentation MT. Voir Disconnect MV Power.
  9. Installez le tablier arrière sous le capot. Voir Underhood Trim - Rear Apron Assembly (Remove and Install).
  10. Remontez la glace avant gauche et fermez la porte avant gauche.