Code de correction NA REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

1. Open LH rear door
   Remarque

   Push LH C-pillar door trigger to release

   

   

2. Lower LH rear window

   

3. Partially release LH rear primary door seal

   

4. Remove LH lower C-pillar trim
   Remarque

   3x clips, 7x tabs, 4x datums, Starting at door sill pull upward then forward to release, Leave trim attached to seat belt

   

   

   

5. Remove 2nd row seatback LH outboard bolster
   Remarque

   2x tabs, 1x datum, 3x clips, Release tab near the bottom of LH outboard bolster, Partially release LH 2nd row shoulder cover and remove bolster from vehicle

   

   

   

   

   

   

   

   

6. Fold up 2nd row 60 seat
   Remarque

   Pull tether to release then lift up until locked in place

   

7. Open RH rear door
   Remarque

   Push RH C-pillar door trigger to release

   

8. Lower RH rear window

   

9. Fold up 2nd row 40 seat
   Remarque

   Pull tether to release then lift up until locked in place

   

   

10. Partially release RH lower C-pillar trim
    Remarque

    1x clip, 1x datum

    

11. Remove rear wall lower trim
    Remarque

    2x push clips, 4x clips, Remove outermost push clips, then pull straight forward to release inner clips

    

    

    

    

    

12. Fold down 2nd row 40 seat
    Remarque

    Pull tether to release then pivot down until locked in place

    

    

13. Disconnect LH 2nd row cushion assembly connectors
    Remarque

    3x connectors, 5x clips

    

    

    

14. Remove LH 2nd row seat cushion outboard cover
    Remarque

    1x clip, Pull outward from lower forward section to release

    

    

    

15. Release LH 2nd row cushion from underbelly
    Remarque

    Pull plastic retainers outward to release from underbelly

    

    

16. Remove LH 2nd row seat underbelly
    Remarque

    8x clips, Pull outwards from bottom to release

    

    

    

17. Remove LH 2nd row cushion assembly
    Remarque

    6x clips, Lift upwards off seat frame

    

    

    

    

    

18. Remove LH 2nd row seat buckle split closeout assembly
    Remarque

    2x clips, 1x datum

    

19. Install LH 2nd row seat buckle split closeout assembly
    Remarque

    2x clips, 1x datum

    

20. Install LH 2nd row cushion assembly
    Remarque

    6x clips, Lower onto seat frame

    

    

    

    

    

21. Install LH 2nd row seat underbelly
    Remarque

    8x clips, Push inwards to engage clips

    

    

    

22. Secure LH 2nd row cushion to underbelly
    Remarque

    Secure plastic retainers in channel

    

    

23. Install LH 2nd row seat cushion outboard cover
    Remarque

    1x clip, Pull outward from lower forward section to release

    

    

    

24. Fold up 2nd row 40 seat
    Remarque

    Pull tether to release then lift up until locked in place

    

    

25. Connect LH 2nd row cushion assembly connectors
    Remarque

    3x connectors, 5x clips

    

    

    

26. Install rear wall lower trim
    Remarque

    2x push clips, 4x clips

    

    

    

    

    

27. Fold down 2nd row 40 seat
    Remarque

    Pull tether to release then pivot down until locked in place

    

    

28. Fold down 2nd row 60 seat
    Remarque

    Pull tether to release then pivot down until locked in place

    

    

29. Install LH lower C-pillar tr
    Remarque

    3x clips, 7x tabs, 4x datums

    

    

    

30. Secure LH rear primary door seal

    

31. Install 2nd row seatback LH outboard bolster
    Remarque

    2x tabs, 1x datum, 3x clips, Position LH outboard bolster into place, Ensure all clips and tabs are fully engaged, Replace any missing or damaged clips, Secure LH 2nd row shoulder cover, Perform push-pull-push test

    

    

    

    

    

    

    

32. Raise LH rear window

    

33. Close LH rear door

    

34. Install RH lower C-pillar trim
    Remarque

    1x clip, 1x datum

    

35. Raise RH rear window

    

36. Close RH rear door