2024-03-05

Speaker - Pedestrian Warning (Remove and Replace)

Code de correction 17541002 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
  1. Open LH front door
  2. Open hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via Controls > Front Trunk
  3. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips
  4. Remove RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  5. Remove LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  6. Release drainage hoses from HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hoses
  7. Remove clips securing HEPA filter inlet duct to cowl panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x push clips
  8. Remove HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips on HEPA filter
  9. Remove HEPA filter outlet duct from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift up, pull towards front of vehicle, then rotate clockwise
  10. Remove front underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips
  11. Disconnect light and release switch connectors and remove underhood storage carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Release edge of carpet from underneath underhood storage unit seal
  12. Remove bolts and clips securing underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 7 Nm, 2x push clips
  13. Remove underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x grommet, Lift the underhood storage unit appropriately to access the grommet and push grommet through underhood storage
  14. Release connector from pedestrian warning audio speaker
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Disengage locking tab, then release connector
  15. Remove nuts securing pedestrian warning audio speaker onto RH shock tower post assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 10mm, 8.5 Nm
  16. Position and install pedestrian warning audio speaker onto RH shock tower post assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 10mm, 8.5 Nm
  17. Connect pedestrian warning audio speaker connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Secure locking tab
  18. Feed harness grommet through underhood storage unit and install underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x grommet, Lift the underhood storage unit appropriately to access the grommet
  19. Install bolts and clips securing underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 7 Nm, 2x push clips
  20. Install underhood storage carpet and reconnect light and release switch connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Secure edges of carpet underneath underhood storage unit seal
  21. Install front underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips
  22. Install HEPA filter outlet duct
  23. Install HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs, One on each side
  24. Install clips securing HEPA filter inlet duct to cowl panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x push clips
  25. Secure drainage hoses to HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hoses
  26. Install LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  27. Install RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  28. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips
  29. Close hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  30. Close LH front door