20/12/2023 17:13:54

Hose - Outlet - Rear Drive Unit (Remove and Replace)

Code de correction 18302502 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Dépose

  1. Open the LH front door and lower the window.
  2. Prepare the vehicle for lifting, but do not raise the vehicle at this stage. See Soulever le véhicule - pont élévateur à 2 poteaux.
  3. Remove the HEPA filter inlet duct. See Conduit - Filtre HEPA - Entrée (retirer et remplacer).
  4. Remove the HEPA filter outlet duct. See Conduit – filtre HEPA – sortie (retrait et remplacement).
  5. Disconnect 12V power. See Disconnect 12V Power.
  6. Remove the mid aero shield panel. See Panneau - bouclier aérodynamique - central (retirer et remplacer).
  7. Install a hose clamp onto the RDU to pump 2 hose.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Install the clamp in front of the clip.
  8. Remove the clip that attaches the RDU outlet hose to the subframe.
  9. Position a coolant drain underneath the RDU.
  10. Remove the RDU outlet hose from the RDU.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Clamp the hose prior to removal. Plug the drive unit once the hose has been removed.
  11. Remove the clip that attaches the RDU to pump 2 hose to the body.
  12. Disconnect the RDU outlet hose from the RDU to pump 2 hose.
  13. Remove the RDU outlet hose from the vehicle.

Installation

  1. Position the RDU outlet hose onto the subframe.
  2. Connect the LRDU outlet hose onto the RDU to pump 2 hose.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The locking tabs must be flush to be fully secured. Perform a push-pull-push test.
  3. Install the clip that attaches the RDU to pump 2 hose to the body.
  4. Remove the plug, and then install the RDU outlet hose onto the RDU.
  5. Install the clip that attaches the RDU outlet hose to the subframe.
  6. Clean any coolant residue from the subframe.
  7. Lower the vehicle until the tires are touching the floor.
  8. Remove the coolant bottle cap.
  9. Reconnect 12V power. See Disconnect 12V Power.
  10. Using Toolbox 3, perform a coolant air purge. See Circuit de refroidissement - remplissage partiel et purge.
  11. Install the mid aero shield panel. See Panneau - bouclier aérodynamique - central (retirer et remplacer).
  12. Remove the vehicle from the lift and disable Jack Mode.
  13. Inspect the coolant level and top off as necessary.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure that the fluid level is at the Max line on the coolant bottle.
  14. Install the coolant bottle cap.
  15. Disconnect the laptop from the vehicle.
  16. Install the HEPA filter outlet duct. See Conduit – filtre HEPA – sortie (retrait et remplacement).
  17. Install the HEPA filter inlet duct. See Conduit – filtre HEPA – sortie (retrait et remplacement).