2024-12-19

Base Assembly - Driver Seat (Model X Seat) (Remove & Replace)

Code de correction 13044012

  • 2024-12-10: Added mini-tilt motor configuration information.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
  1. Open both doors on LH side
  2. Lower both LH side windows
  3. Open hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using MCU touchscreen > Controls > Frunk Trunk
  4. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips
  5. Remove LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  6. Remove RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  7. Release drainage hoses from HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hoses
  8. Remove clips securing HEPA filter inlet duct to cowl panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x push clips
  9. Remove HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips on HEPA filter
  10. Remove HEPA filter outlet duct from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift up, pull towards front of vehicle, then rotate clockwise
  11. Move LH front seat forward
  12. Remove the LH front seat rear track covers
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x covers
  13. Remove bolts securing rear of LH front seat tracks to the floor panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x patch bolt, T40P, 17 Nm, 1x patch bolt, T45P, 34 Nm, Discard after removal
  14. Move LH front seat backward
  15. Remove LH front seat front track covers
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x covers
  16. Remove bolts securing front of LH front seat tracks to the floor panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x patch bolt, T40P, 17 Nm, 1x patch bolt, T45P, 34 Nm, Discard after removal
  17. Adjust position of LH front seat for easy removal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Move seat to middle of track at most upright position with seat fully up off floor
  18. Power down vehicle using MCU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Controls > Safety&Security > Power Off > ''POWER OFF''
  19. Disconnect 12V negative terminal and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components
  20. Disconnect LH front seat connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors
  21. Remove LH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend assistance, Use caution to not damage other components
  22. Lift seat bottom to gain access to seat frame
  23. Release toe kick straps from both sides of interior seat base
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hook clips
  24. Disconnect seat back connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, 1x fir tree clip
  25. Release seat cushion upholstery J-hooks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x hook clips
  26. Disconnect seat bottom connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  27. Release seat connector from spring mat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Slide connector away from seat to release
  28. Remove puddle lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  29. Remove air bag harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x harness clip
  30. Return seat to upright position
  31. Remove LH side shield fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, PH2, 2 Nm
  32. Release LH side shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 1x connector, Do not forcefully remove side shield as seat switch connector will need to be released, Remove side shield starting at the front of seat
  33. Remove RH side shield fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, PH2, 2 Nm
  34. Release RH side shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 1x connector clip
  35. Remove front center panel cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  36. Remove LH outer mic
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Turn LH outer mic counter clockwise and pull up to release
  37. Remove LH inner mic
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Turn LH inner mic clockwise and pull up to release
  38. Remove the outboard fasteners securing the seat back frame to the seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, TP47, 43 Nm, Discard after removal
  39. Remove seat belt buckle from cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 14mm, 40 Nm, 1x connector
  40. Remove the inboard fasteners securing the seat back frame to the cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, TP47, 43 Nm, Discard after removal
  41. Remove the seat back frame from the cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift up on seat back to release from seat cushion frame
  42. Release the retaining clips securing seat bottom near seat buckle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips
  43. Release seat cushion upholstery from seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x J-hook, Starting on LH side of seat cushion upholstery pry J-hook out of seat cushion frame and work your way toward RH side to release seat cushion upholstery
  44. Remove seat cushion upholstery from seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift up on seat cushion to separate from seat cushion frame
  45. Install seat cushion to seat cushion frame
  46. Install seat cushion upholstery to seat cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x J-hook, Starting on RH side of seat cushion upholstery press J-hook into seat cushion frame and work your way toward LH side to secure seat cushion upholstery
  47. Install the retaining clips securing seat bottom near seat buckle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, Press clips on seat cushion frame to secure seat cushion upholstery
  48. Install seat back frame to cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Position seat back frame to seat cushion frame
  49. Install the inboard fasteners securing the seat back frame to the cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, TP45, 43 Nm, Install new patch bolts
  50. Install the outboard fasteners securing the seat back frame to the cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x patch bolts, TP45, 43 Nm, Install new patch bolts
  51. Install the seat belt buckle onto the cushion frame
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 14mm, 40 Nm, 1x connector
  52. Install LH outer mic
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Position LH outer mic to seat back frame and rotate clockwise while pressing down to install
  53. Install LH inner mic
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Position LH inner mic to seat back frame and rotate counter clockwise while pressing down to install
  54. Install front center panel cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  55. Install RH side shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 1x connector clip
  56. Install RH side shield fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, PH2, 2 Nm
  57. Install LH side shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clips, 1x connector
  58. Install LH side shield fastener
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, PH2, 2 Nm
  59. Place the front seat in a position to gain access to the bottom of the seat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Protect seat cushion from damage
  60. Install seat connector to spring mat
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, Slide connector onto spring mat
  61. Connect seat bottom connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  62. Install seat cushion upholstery J-hooks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x hook clips
  63. Install Puddle lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  64. Install air bag jumper harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x harness clip
  65. Install seat back connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, 1x fir tree clip
  66. Secure the toe kick straps from both sides of the interior seat base
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hook clips
  67. Return seat to upright position
  68. Install LH front seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Recommend Assistance, Take care not to damage surrounding components while lifting the seat into the vehicle
  69. Connect LH front seat connectors
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors
  70. Connect First Responder Loop and 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 1x nut, 10mm, 5Nm
  71. Move LH front seat backward
  72. Install bolts securing both LH front seat front tracks to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x patch bolt, T40P, 17 Nm, 1x patch bolt, T45P, 34 Nm, Install new bolts
  73. Install LH front seat front track covers
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x covers
  74. Move LH front seat forward
  75. Install bolts securing both LH front seat rear tracks to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x patch bolt, T40P, 17 Nm, 1x patch bolt, T45P, 34 Nm, Install new bolts
  76. Install LH front seat rear track covers
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x covers
  77. Move LH front seat to original position
  78. Les ensembles de sièges avant de remplacement et les ensembles de cadres de coussins de siège achetés après juin 2024 sont équipés d'un moteur Tesla « mini-inclinaison » de nouvelle conception, et le remplacement de ces pièces (ou du moteur d'inclinaison lui-même) pourrait nécessiter un changement de configuration. Passez en revue les informations de configuration dans le tableau et effectuez les sous-étapes suivantes si une mise à jour de la configuration est nécessaire.
    1. Allez à la section Configuration du véhicule du Tableau de bord d'infodivertissement. Voir Configuration de la passerelle (afficher et modifier).
    2. Mettez à jour cfg_frontSeattype en fonction de la combinaison de moteurs d'inclinaison décrite dans le tableau.
  79. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connecter et déconnecter).
  80. Redeploy the vehicle firmware. See Firmware Reinstall - Toolbox.
  81. Calibrate the seat:
    • To calibrate the driver seat, in Toolbox 3, click the Actions tab, type "PROC_MSMD" into the search field, click PROC_MSMD_VCSEATD-FRONT-DRV_CALIBRATE-MEMORY-SEATvia Toolbox: (link), click Run, and allow the routine to complete.
    • To calibrate the front passenger seat, in Toolbox 3, click the Actions tab, type "PROC_MSMP" into the search field, click PROC_MSMP_VCSEATP-FRONT-PAS_CALIBRATE-MEMORY-SEATvia Toolbox: (link), click Run, and allow the routine to complete.
  82. Disconnect Toolbox and remove the laptop from the vehicle. See Toolbox 3 (Connecter et déconnecter).
  83. Install HEPA filter outlet duct
  84. Install HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs, One on each side
  85. Install clips securing HEPA filter inlet duct to cowl panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x push clips
  86. Secure drainage hoses to HEPA filter inlet duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hoses
  87. Install LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  88. Install RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips
  89. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips
  90. Close hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  91. Raise both LH side windows
  92. Close both doors on the LH side