20/12/2023 17:14:07

Door Assembly - Charge Port (China) (Remove and Replace)

Code de correction 44014302

  • 1080562-00-A Béquille de capot télescopique
  • 1060071-00-A Torque Wrench ¼ in Dr Hexagon
  • 1076921-00-A Fluke 1587
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement

Seuls les techniciens qui ont été sensibilisés aux dangers de la haute tension et qui ont complété toutes les formations de certification requises (le cas échéant) sont autorisés à effectuer cette procédure. Portez toujours un équipement de protection personnelle et des gants isolants haute tension ayant un classement minimal de 0 (1000 volts) avant de manipuler un câble, une barre omnibus ou des raccords haute tension. Se référer à Tech Note TN-15-92-003, Mises en garde relatives à la haute tension pour des informations supplémentaires sur la sécurité.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement

Retirez tous vos bijoux (montres, bracelets, bagues, colliers, boucles d’oreilles, étiquettes d’identification, piercings, etc.) et tous les objets (clés, pièces de monnaie, stylos, crayons, outils, attaches, etc.) de vos poches avant d’effectuer toute procédure vous exposant à un courant haute tension.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement

Proper personal protective equipment (PPE) is required to perform this procedure:

  • High voltage insulating gloves
  • Leather glove protectors
  • High voltage glove tester
  • Safety glasses
  • Electrical hazard rated safety shoes
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement

A glove inflator is the only recommended way to test HV gloves. Both HV gloves must pass testing before beginning this procedure. If either glove does not pass the air check, discard the pair.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement

Make sure that the HV gloves are not expired. HV gloves can be used up to 12 months after the testing date printed on the glove, but only 6 months after first use even if the gloves are still within the 12-month period.

Retirer

  1. Open the LH front door and lower the LH front window.
  2. Move both front seats fully forward.
  3. Open the rear doors, the liftgate, and the charge port door.
  4. Remove the rear underhood apron. See Tablier sous le capot - arrière (retrait et remplacement).
  5. Remove the LH and the RH underhood aprons. See Tablier sous le capot – côté gauche (Retirer et remplacer).
  6. Remove the HEPA filter outlet duct. See Conduit – filtre HEPA – sortie (retrait et remplacement).
  7. On the touchscreen, tap Controls > Charging > Open Charge Port to open the charge port door.
  8. Perform the charge port voltage check. See Vérification de la tension du port de recharge.
  9. Remove the LH trunk side trims. See Garniture - coffre arrière - latérale - côté auche (retrait et remplacement).
  10. Release the clip and the tabs (x6) that attach the painted panel to the charge port door.
    Conseil : Release the clip through opening, and then slide the door away from the vehicle.
  11. Remove the nut that attaches the charge port ground to the body.
    Nous recommandons l’utilisation des outils suivants :
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
    • Rallonge de 6 po
    • Douille de 13 mm
  12. Release the edge clips (x2) that attach the manual release cables to the charge port assembly.
  13. Remove the screw that attaches the latch release cables at the center of the charge port assembly housing, and then move the cables aside.
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
    • Rallonge de 4 po
    • Clé à cliquet/Clé dynamométrique
  14. Disconnect the latch actuators (x2).
  15. Disconnect the logic connector from the charge port ECU.
  16. Release the clips (x2) that attach the HV cables to body studs.
  17. Remove the bolts (x3) that attach the HV harnesses to the charge port housing, and then move the harnesses aside.
    Nous recommandons l’utilisation des outils suivants :
    • Clé à cliquet/Clé dynamométrique
    • Rallonge de 10 po
    • Douille de 10 mm
  18. Remove the bolts (x7) to remove the charge port assembly from the vehicle.
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
    • Rallonge de 4 po
    • Clé à cliquet/Clé dynamométrique
  19. Disconnect the charge port door connector.
  20. Rotate the charge port door assembly out with charge port door open, release the grommet, and then feed the charge port door harness through the body so that the charge port door may be removed.

Installer

  1. Position the charge port door assembly to the vehicle, feed the harness through the body, and then secure the grommet to the body.
    Conseil : Ensure the grommet is fully seated all the way around.
  2. Connect the charge port door connector.
  3. Install the bolts (x7) to secure the charge port assembly to the vehicle.
    6 Nm (4.4 lbs-ft)
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
    • Rallonge de 4 po
    • Clé à cliquet/Clé dynamométrique
  4. Install the bolts (x3) that attach the HV harnesses to the charge port housing.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Ensure that the cable is not tugged or pulled unnecessarily which can yield the C-clamp strain relief and cause a thermal ignition event at the GB charge port area while attempting to charge.
    Nous recommandons l’utilisation des outils suivants :
    • Clé à cliquet/Clé dynamométrique
    • Rallonge de 10 po
    • Douille de 10 mm
    • Rallonge de 4 po
  5. Secure the clips (x2) that attach the HV cables to body studs.
  6. Connect the latch actuators (x2).
  7. Connect the logic connector to the charge port ECU.
  8. Install the screw that attaches the latch release cables at the center of the charge port assembly housing.
    1.5 Nm (1.1 lbs-ft)
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
    • Rallonge de 4 po
    • Clé à cliquet/Clé dynamométrique
  9. Secure the edge clips (x2) that attach the manual release cables to the charge port assembly.
  10. Install the nut that attaches the charge port ground to the body.
    9 Nm (6.6 lbs-ft)
    Nous recommandons l’utilisation des outils suivants :
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
    • Rallonge de 6 po
    • Douille de 13 mm
    • Clé à cliquet/Clé dynamométrique
    • Rallonge de 4 po
  11. Install the clip and the tabs (x6) that attach the painted panel to the charge port door.
    Conseil : Check the orientation of the outer trim prior to the installation (marked on rear of panel).
  12. Install the LH trunk side trims. See Garniture - coffre arrière - latérale - côté auche (retrait et remplacement).
  13. Close the liftgate and the charge port door.
  14. Install the new patch bolts (x11) that secure the HV charger access panel cover.
    2 Nm (1.5 lbs-ft)
    Nous recommandons l’utilisation des outils suivants :
    • Douille Torx T20
    • Rallonge de 2 po
    • Electrical Protective Gloves
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
    • Clé à cliquet/Clé dynamométrique - 1060071-00-A
  15. Use IPA wipes to clean the charger, and then install the new warranty label onto the charger cover panel.
    Conseil : Allow 1 minute for the IPA to dry.
  16. Lower the seat frame into the position, and then secure the harness clips (x8) to the frame.
  17. Install and torque the bolts that attach the seat frame to the vehicle.
    26 Nm (19.2 lbs-ft)
    Nous recommandons l’utilisation des outils suivants :
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
    • Rallonge de 6 po
    • Douille de 11 mm
  18. Place the NVH padding onto seat frame.
  19. Install the connectors (x7, if equipped) and the clips (x2) that secure the seat bottom cushion.
  20. Connect the 12V battery power. See Disconnect 12V Power.
  21. Install the LH and the RH underhood aprons. See Tablier sous le capot – côté gauche (Retirer et remplacer).
  22. Install the rear underhood apron. See Tablier sous le capot - arrière (retrait et remplacement).
  23. Return both front seats to the original positions.
  24. Raise all windows and close all doors.