20/12/2023 17:13:57

Large Drive Unit Inverter Isolation Check

Code de correction 40200500 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 2023-03-27: Condensed procedure with links to supplemental procedures, including isolation/insulation test.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est un BROUILLON, même si elle a été validée. Il peut manquer des avertissements et des mises en garde. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près de systèmes et de composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Procédure

  1. Move the vehicle to a two-post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.
  2. Remove the rear underhood apron. See Tablier sous le capot - arrière (retrait et remplacement).
  3. Remove the RH underhood apron. See Tablier sous le capot – côté gauche (Retirer et remplacer).
  4. Disconnect 12V power. See Disconnect 12V Power.
  5. Remove the mid aero shield panel. See Panneau - bouclier aérodynamique - central (retirer et remplacer).
  6. Disconnect the electrical harness from the rear drive unit inverter low voltage connector.
  7. Completely loosen the bolt, and then remove the rear drive unit inverter HV cover from the rear drive unit inverter.
  8. Remove and discard the O-rings (x2) from the rear drive unit inverter HV cover.
  9. Perform an isolation/insulation test of the rear drive unit inverter HV terminals. See Test d’isolement/isolation.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    For this test:
    • Set the test voltage to 500V
    • Measure resistance at the B+ and B- terminals of the rear drive unit inverter and record value
    • Measure voltage at the B+ and ground, B- and ground, and B+ and B-
    • Do not remove the probes from the terminals until the voltage has dropped to 10V or less.
  10. Lubricate the new rear drive unit inverter HV cover O-rings with silicone lubricant, and then install the O-rings onto the rear drive unit inverter HV cover.
  11. Postion the rear drive unit inverter HV cover over the rear drive unit inverter low voltage connector, press the cover in, and then tighten the bolt that attaches the cover to the rear drive unit inverter.
    3 Nm (2.2 lbs-ft)
  12. Connect the electrical harness to the rear drive unit inverter low voltage connector.
  13. Install the mid aero shield panel. See Panneau - bouclier aérodynamique - central (retirer et remplacer).
  14. Connect 12V power. See Disconnect 12V Power.
  15. Install the RH underhood apron. See Tablier sous le capot – côté gauche (Retirer et remplacer).
  16. Install the rear underhood apron. See Tablier sous le capot - arrière (retrait et remplacement).
  17. Remove the vehicle from the two-post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.