2025-09-30

Hv Battery (RWD) (Remove and Replace)

Code de correction 16010102 4.68 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiquespour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
  • 2025-07-10: Released new procedure.

Retirer

  1. Remove the HV battery. See HV Battery (RWD) (Remove and Install)
  2. Si la batterie HT st expédiée, attachez l'ancien sectionneur pyro de la batterie aux supports du couvercle du compartiment auxiliaire de l'ancienne batterie HT à l'aide de serre-câbles. Si le couvercle du compartiment auxiliaire n'est pas équipé de supports, fixez l'ancien sectionneur pyro de la batterie au coin arrière droit de l'ancienne batterie HT à l'aide de serre-câbles.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Placez un morceau de papier sous le sectionneur pyro de la batterie. Utilisez du ruban de masquage si nécessaire pour empêcher tout mouvement.
    Figure 1. Sectionneur pyro de la batterie fixé aux supports sur le couvercle du compartiment auxiliaire
    Figure 2. Sectionneur pyro de la batterie fixé au coin arrière droit de la batterie HT
  3. Attach HV battery H-frame to the gantry and raise it into position.
  4. Position the HV battery under the gantry.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Assistance recommended. If the original pack is RWD and supplied pack is DM, center ski transfer is required.
  5. Lower H-frame onto the old HV battery and secure the H-frame to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x bolts, 8mm Allen, Hand tight
  6. Raise the old HV battery off the battery table.
  7. Position the gantry over a pallet.
  8. Lower the HV battery onto the pallet.
  9. Remove H-frame from the old HV battery.
  10. Raise gantry and H-frame from the old HV battery.

Installer

  1. Open the crate top housing the new HV battery pack.
  2. Remove nuts that attach the new HV battery to the crate.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x nuts, 15mm
  3. Position the gantry over the new HV battery crate and secure the H-frame to the battery.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x bolts, 8mm Allen, Hand tight
  4. Lift the new HV battery out of the crate.
  5. Move the gantry away from the HV battery crate and over the HV battery table.
  6. Lower the HV battery onto the battery table.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure to align the HV battery onto the center ski.
  7. Release the H-frame from the HV battery and raise the gantry.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x bolts, 8mm Allen, Hand tight
  8. Remove the HV battery from under the gantry.
  9. Position the gantry over the old HV battery.
  10. Lower the H-frame onto the old HV battery and secure the H-frame to the HV battery.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x bolts, 8mm Allen, Hand tight
  11. Raise the old HV battery above the HV battery crate.
  12. Position the HV battery crate underneath the old HV battery.
  13. Lower the old HV battery into the crate.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use caution to align the 4 studs and not damage the battery.
  14. Remove the H-frame from the old HV battery.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x bolts, 8mm Allen, Hand tight
  15. Raise gantry and H-frame from the old HV battery.
  16. Lower the gantry and remove the HV battery H-frame from the gantry.
  17. Install the nuts that attach the HV battery to the crate hand tight.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x nuts, 15mm
  18. Close the crate top housing the old HV battery.
  19. Install HVC logic cap onto the new HV battery.
  20. Install penthouse engagement seal onto the HV battery pack.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    This seal is a one time use item and should be replaced each time an HV battery pack is removed from the vehicle or installed onto a new HV battery pack if not equipped.
  21. Install the HV battery. See HV Battery (RWD) (Remove and Install)
  22. Connect LV battery maintenance charger.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Release the positive terminal cover. Attach the positive terminal to the jump post. Attach the negative terminal to the ground terminal located above the VCfront. Connect the maintainer to power supply. To avoid damaging the vehicle. DO NOT allow the positive cable to make contact with other metal components. Never have a float charger and the LV battery simultaneously connected for any extended period of time (apart from during a SW reinstall/CAN redeploy).
  23. Enable Service Mode Plus. See Mode Entretien Plus
  24. Access High Voltage System routines using the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select Service mode plus > High Voltage
  25. Select "High Voltage Battery Replacement" through the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Procedures > High Voltage Battery Replacement.
  26. Select "Software Reinstall" through the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Software Reinstall > CAN ECU > Reinstall, Allow routine to complete, ensure routine is successful
  27. Exécutez la routine ODIN
  28. Disconnect the LV maintainer from the vehicle.