2026-05-28

Trim Cover - 60 Seatback - 2nd Row (7-Seat) (Remove and Replace)

Code de correction 13080300302 FRT 1.08 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

  • 2026-05-04: Released new procedure.

Retirer

  1. Remove the 2nd row LH seat assembly. See Ensemble de siège - 2e rangée - gauche (7-places) (retirez et remplacez).
  2. Remove the 2nd row 60 seatback assembly toe kick panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips. Pry up on LH side of 60 toe kick cover to release the clips. Repeat on RH side to fully remove.
  3. Release the 60 seat side shield.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clip, 1x hook, 1x connector. Once push clip is removed, lift up and out on the 60 seat side shield to release it. Use caution when releasing the side shield as seat fold switch harness is short.
  4. Remove the center back panel from the 2nd row center seatback.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 2 hooks. Lift up at the lower 20 back panel and then slide forward to release.
  5. Remove the 2nd row 60 seatback panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips, 2x hooks. Release the clips starting at the top of the back panel working your way down the lower back panel. Pull 60 back panel towards the front of the vehicle to remove it.
  6. Remove the center seatback lumbar bun fastener.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 1.5 Nm
  7. Remove the center seatback lumbar bun.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips. Pull bolster outwards to release it.
  8. Remove the center seatback pivot clamps.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, T40, 22 Nm. Once fasteners are removed, slide the pivot clamp towards the center of the center seatback and pull each outwards to remove.
  9. Manually release the center seatback latch.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use a small screwdriver to manipulate the center seatback latch to release.
  10. Remove the center seatback from the 60 seat frame.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove center seatback by lifting it upwards.
  11. Release the 2nd row 60 seat harness connectors and unclip them from the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clip, 5x connectors.
  12. Release the clips and remove the inboard outer trim from the 2nd row 60 seat cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips. Use a trim tool to unclip the three clips and remove the inboard outer trim towards the rear of the vehicle.
  13. Remove the push clips for the 2nd row 60 bottom seat pan.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips. Remove push clips from the front of the seat pan.
  14. Remove the fasteners that attach the 60 seat pan to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip. Remove remaining bolts attaching the seat pan to the seat frame.
  15. Remove the headrest from the 2nd row 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening. Lift up while engaged.
  16. Remove the headrest guides from the 2nd row 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull back on the lower portion of the headrest guide to release the tab while also applying upward force to remove the headrest guides.
  17. Release the harness from the 2nd row 60 seatback.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors, 3x clips.
  18. Remove the 2nd row 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips. Release the clips that attach the 60 seatback and lift upwards. The seat belt will be removed in a later step.
  19. Slightly lift the 60 seat cushion pan upward.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift 60 seat cushion upward but do not fully remove it at this time.
  20. Disconnect the seat cables from the floor latch and easy entry actuators on the 60 seat.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  21. Remove the 2nd row 60 seat cushion assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove seat bottom by lifting the rear first and removing it towards the front of the seat.
  22. Remove the 2nd row center seat belt anchor.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T50, 40 Nm. Discard the bolt after removal.
  23. Remove the 2nd row center seat belt guide.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 2x datums.
  24. Remove the 2nd row center seat belt from the 2nd row 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pass the seat belt through the opening.
  25. Put the 2nd row 60 seatback assembly on a suitable working surface.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Avoid damage to the seat cover.
  26. Remove the easy-entry switch.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 1x connector.
  27. Release the 2nd row 60 seatback cover.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    16x tabs. Pull material downward to release it.
  28. Remove the seatback cover from the foam.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x hogring. Hook & loop the attachment around the perimeter. Cut hogrings, clean debris. If 40/60 seat that is not being repaired does not have ISOFIX flag for child seats, the seat covers will also require replacement.

Installer

  1. Install the seatback cover onto the foam.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    16x hooks. Pull the material downward to attach it. Make sure that the material is distributed evenly on the visible side.
  2. Secure 2nd row 60 seatback cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    16x tabs, Pull material downward to secure tabs and align material
  3. Install the easy-entry switch.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x tabs, 1x connector.
  4. Install the 2nd row center seat belt to the 2nd row 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pass the seat belt through the opening.
  5. Install the 2nd row center seat belt guide.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 2x datums.
  6. Install a new bolt that attaches the 2nd row center seat belt anchor.
    40 Nm (29.5 lbs-ft)
  7. Connect the seat cables from the floor latch and easy entry actuators onto the 60 seat.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips.
  8. Put the 60 seat pan onto the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Reinstall the seat bottom onto the seat frame by starting at the rear of the seat.
  9. Install the 60 seat pan.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips. Push the front of the seat cushion back into place and install the clips.
  10. Install the fasteners that attach the 60 seat pan to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip.
  11. Install the 2nd row 60 seatback.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips. Slide seatback into position and make sure that the bottom retainers slide into place. Reinstall the push clips to attach the seatback.
  12. Install the headrest guides into the 60 seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Install the headrest guides by pressing them downwards until the lower tab is seated.
  13. Install the headrest onto the 60 seat assembly.
  14. Install the harness onto the 2nd row 60 seatback.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x connectors, 3x clips.
  15. Install the center seatback pivot clamps.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, T40, 22 Nm. Insert the pivot clamp at the center of the center frame and slide it outwards to install the bolts. When replacing pivot clamps, they must be replaced in pairs.
  16. Install the center seatback lumbar bun.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips. Press seatback lumbar bun into the center frame.
  17. Install the inboard outer trim to the 60 seat.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips. Install inboard outer trim and reseat the clips.
  18. Install the 60 seat side shield.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clips, 1x hook, 1x connector, . Lift up on the front of the side shield and seat the hook into the seat cushion assembly.
  19. Install the center seatback lumbar bun fastener.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T20, 1.5 Nm.
  20. Insert the back panel hooks into the center seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hooks. Engage the hooks and slide rearward into position. Early production vehicles may have 4x hooks.
  21. Insert the back panel hooks into the 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x hooks.
  22. Install the 60 seatback panel onto the seatback.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x clips. Install the back panel clips to the seatback frame starting at the lower back panel, working your way up towards the upper back panel.
  23. Install the 60 seat toe kick cover.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips.
  24. Install the 2nd row 60 seat harness connectors and clip them onto the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x clip, 5x connectors.
  25. Install the 2nd row 60 seat assembly. See Ensemble de siège - 2e rangée - gauche (7-places) (retirez et remplacez).
  26. Enable Service Mode. See Mode Entretien.
  27. Unlock the vehicle Gateway. See Passerelle (déverrouiller).
  28. Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) : PROC_VCLEFT_X_2R-SEAT-RECLINE-CALIBRATIONvia Service Mode:Low Voltage ➜ Second Row Seats ➜ Calibratevia Toolbox:(link)
  29. Exit Service Mode. See Mode Entretien.