Code de correction 40202000 0.60 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

1. Raise and support the vehicle. See Soulever le véhicule - pont élévateur à 2 poteaux.
2. Open LH front door

   

3. Lower LH front window

   

4. Exécutez la routine ODIN PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
5. Unlock the vehicle gateway. See Passerelle (déverrouiller).
6. Access thermal system routines via UI
   Remarque

   Select Service mode > Thermal

   

   

7. Perform "Start Thermal Fill/Drain (Coolant Only)" through Service UI
   Remarque

   Select Thermal > Coolant System > Coolant Fill/Drain, click Run, close once routine is completed, Thermal Fill Drain routine has a 5 hour time limit, After 5 hours routine must be performed again

   

   

   

8. Disconnect LV power. See LV Power (Disconnect and Connect) (Modify).
9. Remove the front aero shield. See Aero Shield - Front (Remove and Replace).
10. Remove clips secure LH wheel liner to front fascia and valance
    Remarque

    3x push clips

    

11. Remove clips secure RH wheel liner to front fascia and valance
    Remarque

    3x push clips

    

12. Remove both side bolts securing valance to fascia
    Remarque

    2x bolts, T40, 2.5Nm

    

    

13. Secure RH front wheel liner aside
    Remarque

    1x bungee strap, Secure to subframe

    

14. Position coolant drain container underneath RH front of HV battery

    

15. Attach hose extension to coolant drain hose for extra length

    

16. Attach the powertrain (PT) flush fitting adapter to coolant cart pressure hose

    

17. Disconnect PT return hose
    Remarque

    1x spring clip, Plug coolant connections as needed, Loss of coolant greater than 1L requires coolant vacuum fill

    

    

18. Attach PT drain fitting adapter to male PT return hose

    

    

    

19. Disconnect PT supply hose
    Remarque

    1x spring clip, Plug coolant connections as needed, Loss of coolant greater than 1L requires coolant vacuum fill

    

    

20. Attach PT flush fitting adapter to female side of PT supply hose
    Remarque

    1x spring clip, Perform push-pull test to verify adapter is fully engaged

    

    

    

21. Attach PT drain fitting adapter to coolant pressure tester cart
    Remarque

    The regulator valve is pre-set to 20 psi, When valve is set to horizontal position it is fully closed, Verify valve is in closed position

    

22. Attach compressed air line to coolant pressure tester
    Remarque

    Verify valve is in closed position

    

23. Open valve on PT drain fitting adapter
    Remarque

    When valve is in the vertical position it is fully open

    

24. Slowly open valve on pressure regulator and allow coolant to drain out of PT return hose
    Remarque

    Open valve very slowly, If opened too quickly, pressure relief valve on superbottle cap may open, Also superbottle cap may make humming noise, If so, pressure is too high and should be lowered by adjusting the valve

    

25. Close valve on pressure regulator
    Remarque

    Turn valve knob horizontal when coolant is no longer visibly draining

    

26. Remove PT flush fitting adapter from female side of PT supply hose
    Remarque

    1x spring clip

    

27. Remove plugs then connect PT supply hose
    Remarque

    1x clips, 1x plugs, Perform push-pull-push test to make sure hose is fully engaged. Loss of coolant greater than 1L requires coolant vacuum fill

    

    

28. Disconnect PT flush fitting adapter from female side of PT return tube
    Remarque

    1x spring clip

    

29. Remove PT drain fitting adapter from male side of PT return hose
    Remarque

    1x spring clip, Plug the PT return hose

    

30. Remove plugs then connect PT return tube
    Remarque

    Effectuez un test pousser-tirer-pousser pour vous assurer que le flexible est bien en place. Ne remuez pas le tuyau près de la connexion.

    

    

31. Remove PT drain fitting adapter from cart drain hose

    

32. Remove coolant drain container from underneath vehicle

    

33. Release RH front wheel liner
    Remarque

    1x bungee strap, Remove bungee strap as needed

    

34. Install bolt securing RH front wheel liner to skid plate
    Remarque

    1x bolt, 10mm, 5 Nm

    

35. Install clip securing RH wheel liner to body
    Remarque

    1x push clip

    

36. Install the front aero shield. See Aero Shield - Front (Remove and Replace).
37. Perform a coolant vacuum refill. See Cooling System - Vacuum Refill (Test/Adjust).
38. Connect LV power. See LV Power (Disconnect and Connect) (Modify).
39. Access thermal system routines via UI
    Remarque

    Select Service mode > Thermal

    

    

40. Unlock the vehicle gateway. See Passerelle (déverrouiller).
41. Exécutez la routine ODIN PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAINvia Service Mode:
    • Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    via Toolbox:(link)
    Remarque

    For non China Model Y L vehicles, run "PROC_VCFRONT2_X_STOP-THERMAL-FILL-DRAIN".
42. Exécutez la routine ODIN TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    via Toolbox:(link)
    Remarque

    For non China Model Y L vehicles, run "TEST_VCFRONT2_X_THERMAL-COOLANT-AIR-PURGE-START".
43. Inspect coolant level and top off as necessary
    Remarque

    Ensure that fluid level is at Max line, Vacuum fill required if greater than 1L lost during repair

    

44. Install coolant bottle cap

    

45. Exécutez la routine ODIN PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
46. Install HEPA filter assembly
    Remarque

    2x bolts, 10mm, 10 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct

    

    

    

    

47. Install rear apron
    Remarque

    16x trim clips, 3x locator pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron

    

    

    

48. Close hood

    

    

49. Raise LH front window

    

50. Close LH front door