Korrekturcode 18300192 1.92 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

1. Raise and support vehicle
   Anmerkung

   Ensure vehicle is not charging, Remove charging cable if it's plugged in, Note the MYSP lifting points are more narrow than the MY

   

   

   

   

2. Open all four doors
3. Lower all four windows
4. Connect to vehicle using Toolbox 3.0
   Anmerkung

   Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle. https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)If RJ45 ethernet diagnostic connector present connect directly from laptop using an RJ45 Ethernet cable

   

   

   

5. Select ‘Actions/Autodiag’ tab and search for ‘Fill Drain’

   

6. Select ‘PROC_VCFRONT_X_THERMAL-FILL-DRAINSearch for routine in ToolboxThermal Fluid Fill/Drain’, click ‘Run’, and allow routine to complete
   Anmerkung

   This will ensure the octovalve is in the Series position, Coolant pumps will also be disabled, Once run is selected routine is in progress despite the prompt with loading circle, Routine will time out after several hours and return valves to parallel position if unattended, Select 'X' at top right of window to close once complete

   

   

   

7. Remove laptop from vehicle
   Anmerkung

   Do not close Toolbox 3.0, we will need to resume later

   

8. Move LH front seat forward

   

9. Move RH front seat forward

   

10. Remove 2nd row seat cushion
    Anmerkung

    1x connector, Lift front edge of seat cushion upward to release foam from frame

    

    

    

11. Open hood

    

    

    

12. Remove rear apron
    Anmerkung

    14x clips

    

    

13. Power off vehicle from center display
    Anmerkung

    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box

    

    

14. Disconnect 12V negative terminal and first responders loop
    Anmerkung

    1x nut, 10mm, 6 Nm, 1x connector, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V, Negative terminal should be disconnected before FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

15. Remove all items from pockets and ensure not wearing metal items

    

    

16. Inspect HV insulating gloves
    Anmerkung

    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves. https://service.teslamotors.com/protected-doc/ServiceBulletins/External/TN/TN-15-92-003_High_Voltage_Awareness_Care_Points_R4.pdf

    

17. Put on HV insulating gloves and leather over gloves
    Anmerkung

    Make sure to wear Electrical Protective Gloves any time Hioki tester is used

    

18. Remove bolts securing ancillary bay probe lid cover to ancillary bay cover
    Anmerkung

    2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal

    

19. Remove ancillary bay probe lid cover from ancillary bay cover

    

20. Verify no high voltage
    Anmerkung

    Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

21. Inspect ancillary bay probe lid cover gasket then position onto the ancillary bay cover
    Anmerkung

    Confirm no visual damage present, Replace gasket if damage is found

    

    

22. Install the bolts securing ancillary bay probe lid cover to ancillary bay cover
    Anmerkung

    2x bolts, EP10 5-Lobe, 6 Nm, Install new fasteners

    

23. Remove HV insulating gloves

    

24. Remove LH rear wheel cap
    Anmerkung

    1x cap, Use both hands to gently pull the wheel cap to release the clips, Wheels may be equipped with center caps

    

25. Loosen LH rear wheel
    Anmerkung

    5x nuts, 21mm, 175 Nm

    

26. Close all four doors
    Anmerkung

    Unlatch rear doors at later step

    

27. Raise vehicle partially and lower lift onto locks
    Anmerkung

    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

28. Remove LH rear wheel
    Anmerkung

    5x nuts, 21mm, 175 Nm

    

29. Remove clips securing RH rear wheel liner to rear fascia assembly
    Anmerkung

    3x push clips

    

    

30. Remove clips securing LH rear wheel liner to rear fascia assembly
    Anmerkung

    3x push clips

    

    

31. Raise vehicle fully and lower lift onto locks
    Anmerkung

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

32. Remove mid aero shield
    Anmerkung

    11x bolts, 10mm, 5 Nm, Fasteners may vary, MYSP will have one less bolt and an extra clip

    

33. Remove bolts securing rear diffuser to body
    Anmerkung

    9x bolts, 10mm, 4 Nm

    

34. Remove clips securing rear diffuser to body and remove from vehicle
    Anmerkung

    6x push clips

    

35. Remove LH rear suspension cover
    Anmerkung

    1x bolt, 10mm, 6 Nm, 2x tabs

    

36. Remove RH rear suspension cover
    Anmerkung

    1x bolt, 10mm, 6 Nm, 2x tabs

    

37. Disconnect RH side 12V subframe harness connector
    Anmerkung

    1x connector, Release locking tab

    

38. Remove RH side 12V subframe harness clip from body
    Anmerkung

    1x clip

    

39. Disconnect LH side 12V subframe harness connector
    Anmerkung

    1x connector, Release locking tab

    

40. Remove LH side 12V subframe harness clip from body
    Anmerkung

    1x clip

    

41. Remove nut securing RDU ground strap to vehicle
    Anmerkung

    1x nut, 10mm, 10 Nm

    

42. Remove nut securing LH rear stabilizer bar end link to stabilizer bar
    Anmerkung

    1x nyloc nut, 15mm, 55 Nm, Break nut loose then counter-hold ball joint with 5mm hex, Discard after removal

    

43. Remove stabilizer bar from LH rear end link
    Anmerkung

    May need to move the stabilizer bar up/down to get the correct angle to remove end link, Use a pry bar as needed for assistance

    

44. Remove nut securing RH rear stabilizer bar end link to stabilizer bar
    Anmerkung

    1x nyloc nut, 15mm, 55 Nm, Break nut loose then counter-hold ball joint with 5mm hex, Discard after removal

    

45. Remove stabilizer bar from RH rear end link
    Anmerkung

    May need to move the stabilizer bar up/down to get the correct angle to remove end link, Use a pry bar as needed for assistance

    

46. Position support stand to support front portion of rear subframe

    

47. Remove bolts securing stabilizer bar to subframe
    Anmerkung

    4x patch bolts, 11mm, 30 Nm, Discard after removal

    

48. Lower support stand and remove stabilizer bar from vehicle

    

49. Remove support stand from under vehicle

    

50. Release clips securing coolant hoses to LH shear plate
    Anmerkung

    2x fir tree clips

    

51. Release LH side hose clip from rear battery skid plate
    Anmerkung

    2x clips, Clip quantity may vary on older vehicles

    

52. Release RH side hose clips from rear battery skid plate
    Anmerkung

    2x fir tree clips

    

53. Release clips securing coolant hoses to RH shear plate
    Anmerkung

    2x fir tree clips

    

54. Position coolant drain container underneath LH RDU area
    Anmerkung

    Position neck to catch all coolant loss

    

55. Disconnect RDU inverter inlet hose from fluid coupling
    Anmerkung

    1x spring clip, 2x plugs, Plug ends as needed

    

56. Remove coolant drain container from underneath vehicle

    

57. Release RDU inverter inlet tube from RDU HV cable harness
    Anmerkung

    1x fir tree clip

    

58. Remove bolt securing RDU HV cable bracket to RDU
    Anmerkung

    1x bolt, 10mm, 6 Nm

    

59. Disconnect RDU HV cable from RDU
    Anmerkung

    1x connector, Red locking tab

    

60. Perform RDU diode test
    Anmerkung

    Verify RDU HV cable is disconnected from HV battery. Use a multimeter in diode mode, with the positive DMM probe to B- of the inverter and the negative probe to B+. Pin #1 on HV cables is B- and Pin #2 is B+. MOSFET acceptable diode reading:1.0 - 2.0 V. IGBT acceptable diode reading 0.45 - 2 V (if you get OL or > 2V for a reading you most likely have the probes installed the wrong way around)

    

    

    

61. Release RDU logic connection
    Anmerkung

    1x connector, Do not get coolant ingress into this connector, Move aside as needed

    

62. Release RDU logic connection clip
    Anmerkung

    1x clip

    

63. Place subframe lifting tool into position underneath rear subframe

    

64. Connect air supply to subframe lifting tool

    

65. Raise subframe lifting tool to support rear subframe
    Anmerkung

    3x straps, Attach metal hooks at the end of straps to rings on subframe lifting tool and pull straps until secure, Lower the vehicle if necessary, Recommend assistance

    

    

    

    

66. Remove smaller fasteners for LH shear plate
    Anmerkung

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles.

    

67. Remove large bolt securing LH shear plate and subframe to body and remove shear plate
    Anmerkung

    1x bolt, 21mm, 130 Nm

    

68. Install LH front extension bolt securing subframe to body
    Anmerkung

    1x bolt, 21mm, 10 Nm, During lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height as possible

    

69. Remove smaller fasteners for RH shear plate
    Anmerkung

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles.

    

70. Remove large bolt securing RH shear plate and subframe to body and remove shear plate
    Anmerkung

    1x bolt, 21mm, 130 Nm

    

71. Install RH front extension bolt securing subframe to body
    Anmerkung

    1x bolt, 21mm, 10 Nm, During lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height as possible

    

72. Remove LH rear bolt securing subframe to body
    Anmerkung

    1x bolt, 21mm, 165 Nm

    

    

73. Install LH rear extension bolt securing subframe to body
    Anmerkung

    1x bolt, 21mm, 10 Nm, During lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height as possible

    

74. Remove RH rear bolt securing subframe to body
    Anmerkung

    1x bolt, 21mm, 165 Nm

    

    

75. Install RH rear extension bolt securing subframe to body
    Anmerkung

    1x bolt, 21mm, 10 Nm, During lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height as possible

    

76. Partially lower the subframe and rear drive unit assembly from the vehicle
    Anmerkung

    Use caution while lowering subframe to avoid damage to surrounding components, The descending height is about 13cm

    

    

77. Release clip securing inverter to cooler hose to inverter and remove hose
    Anmerkung

    1x spring clip

    

78. Release clips securing inverter coolant hose
    Anmerkung

    4x clips

    

79. Release RDU inverter coolant hose from heat exchanger and remove hose
    Anmerkung

    1x spring clip

    

    

80. Secure inverter to cooler hose to cooler
    Anmerkung

    1x spring clip, Perform push-pull-push test to make sure hose is fully seated

    

    

81. Secure clips holding inverter to coolant hose to RDU
    Anmerkung

    4x clips

    

82. Secure inverter to cooler hose to inverter
    Anmerkung

    1x spring clip, Perform push-pull-push test to make sure hose is fully seated

    

83. Raise drive unit and subframe into position
    Anmerkung

    Use caution to not damage components while raising subframe

    

84. Remove the RH rear extension bolt from the body
    Anmerkung

    1x bolt, 21mm, 10 Nm, Remove with ratchet wrench

    

85. Install RH rear bolt securing rear subframe to body hand tight
    Anmerkung

    1x bolt, 21mm, 165 Nm, Torque at later step

    

    

86. Remove the LH rear extension bolt from the body
    Anmerkung

    1x bolt, 21mm, 10 Nm, Remove with ratchet wrench

    

87. Install LH rear bolt securing rear subframe to body hand tight
    Anmerkung

    1x bolt, 21mm, 165 Nm, Torque at later step

    

    

88. Remove the LH front extension bolt from the body
    Anmerkung

    1x bolt, 21mm, 10 Nm, Remove with ratchet wrench

    

89. Install bolt and shear plate to LH side of rear subframe hand tight
    Anmerkung

    1x bolt, 21mm, 130 Nm, Torque at later step

    

90. Install bolts securing LH rear shear plate to body hand tight
    Anmerkung

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles. Torque at later step.

    

91. Remove the RH front extension bolt from the body
    Anmerkung

    1x bolt, 21mm, 10 Nm, Remove with ratchet wrench

    

92. Install bolt and shear plate to RH side of rear subframe hand tight
    Anmerkung

    1x bolt, 21mm, 130 Nm, Torque at later step

    

93. Install bolts securing RH shear plate to HV battery hand tight
    Anmerkung

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles. Torque at later step.

    

94. Torque bolts securing shear plates to vehicle
    Anmerkung

    4x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles.

    

    

95. Torque bolt securing subframe and LH rear shear plate to body
    Anmerkung

    1x bolt, 21mm, 130 Nm, Mark bolt after torque

    

    

96. Torque bolt securing subframe and RH rear shear plate to body
    Anmerkung

    1x bolt, 21mm, 130 Nm

    

97. Torque bolt securing RH rear of subframe to body
    Anmerkung

    1x rear bolt, 21mm, 165 Nm, Mark bolt after torque

    

    

98. Torque bolt securing LH rear of subframe to body
    Anmerkung

    1x rear bolt, 21mm, 165 Nm, Mark bolt after torque

    

    

99. Install clips securing coolant hoses to RH shear plate
    Anmerkung

    2x fir tree clips

    

100. Install clips securing coolant hoses to LH shear plate
     Anmerkung

     2x fir tree clips

     

101. Lower rear subframe lifting tool from vehicle
     Anmerkung

     Verify yellow safety straps are removed from subframe

     

     

     

     

102. Disconnect air supply from subframe lifting tool

     

103. Remove subframe lifting tool from underneath vehicle

     

104. Secure RDU logic connection clip
     Anmerkung

     1x clip

     

105. Secure RDU logic connector
     Anmerkung

     1x connector, Verify there is no coolant ingress in connector

     

106. Connect RDU HV cable to RDU
     Anmerkung

     1x connector, Install HV connector lever lock to RDU HV cable connector, Align connector to RDU then remove HV connector lever lock before fully latch connector, Use one hand to support the connector while other latching locking tab, Once installed, verify that the latch is not damaged and fully secured in the latched position

     

     

     

     

107. Install bolt securing RDU HV cable bracket to RDU
     Anmerkung

     1x bolt, 10mm, 6 Nm

     

108. Remove hose plugs and connect coolant inlet hose to rear drive unit
     Anmerkung

     1x spring clip, Let coolant drain from hose before install, Perform push-pull-push test to make sure hose is fully seated

     

109. Secure RDU inverter inlet hose clip onto HV cable
     Anmerkung

     1x fir tree clip

     

110. Install RH side hose clips to rear battery skid plate
     Anmerkung

     2x fir tree clips

     

111. Install LH side hose clip to HV battery rear skid plate enclosure
     Anmerkung

     2x clips, Clip quantity may vary on older vehicles

     

112. Place stabilizer bar into position for installation and raise stand to support stabilizer bar

     

113. Install bolts securing stabilizer bar to subframe
     Anmerkung

     4x patch bolts, 11mm, 30 Nm, Install new patch bolts

     

114. Position LH rear end link into stabilizer bar
     Anmerkung

     Adjust the end link to align with stabilizer bar, Also may need to move the stabilizer bar up/down to get the correct angle to install end link

     

115. Install nut securing LH rear end link to stabilizer bar
     Anmerkung

     1x nyloc nut, 15mm, 55 Nm, Counter-hold ball joint with 5mm hex, Install new nyloc nut, Mark bolt after torque

     

116. Position RH rear end link into stabilizer bar
     Anmerkung

     Adjust the end link to align with stabilizer bar, Also may need to move the stabilizer bar up/down to get the correct angle to install end link

     

117. Install nut securing RH rear end link to stabilizer bar
     Anmerkung

     1x nyloc nut, 15mm, 55 Nm, Counter-hold ball joint with 5mm hex, Install new nyloc nut, Mark bolt after torque

     

118. Torque nut securing RH rear stabilizer bar end link to stabilizer bar
     Anmerkung

     1x nyloc nut, 15mm, 55 Nm, Mark bolt after torque

     

119. Remove support stand from under vehicle

     

120. Install the RDU ground strap to body
     Anmerkung

     1x bolt, 10mm, 10 Nm

     

121. Install LH side 12V subframe harness clip to body
     Anmerkung

     1x clip

     

122. Connect LH side 12V subframe harness connector
     Anmerkung

     1x connector, Engage locking tab

     

123. Install RH side 12V subframe harness clip to body
     Anmerkung

     1x clip

     

124. Connect RH side 12V subframe harness connector
     Anmerkung

     1x connector, Engage locking tab

     

125. Install rear diffuser to rear fascia assembly and secure clips to body
     Anmerkung

     6x clips

     

126. Apply Loctite 222 onto rear diffuser bolts and install bolts securing rear diffuser to body
     Anmerkung

     9x bolts, 10mm, 4 Nm

     

     

127. Lower vehicle partially and set onto locks
     Anmerkung

     Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

     

     

128. Install LH rear wheel
     Anmerkung

     5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

     

129. Lower vehicle until tires are touching the ground
     Anmerkung

     Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

     

     

     

130. Torque LH rear wheel
     Anmerkung

     5x nuts, 21mm, 175 Nm

     

131. Install LH rear wheel cap
     Anmerkung

     1x cap, Align valve stem with wheel cap cavity

     

132. Open all four doors
     Anmerkung

     Latch rear doors to prevent accidental closure

     

133. Remove coolant bottle cap

     

134. Inspect coolant level and top off as necessary
     Anmerkung

     Ensure coolant is filled using G-48 coolant

     

135. Connect first responder loop and 12V negative terminal
     Anmerkung

     1x nut, 10mm, 6 Nm, 1x connector, Engage locking tab, Connect FRL first before connecting 12V to avoid damage to car computer

     

     

136. Install 2nd row seat cushion
     Anmerkung

     1x connector, Slide rear cushion rearward then align foam with seat rail, Make sure cushion is fully seated with push & pull test

     

     

     

137. Move RH front seat to original position

     

138. Move LH front seat to original position

     

139. Connect to vehicle using Toolbox 3.0
     Anmerkung

     Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle. https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)If RJ45 ethernet diagnostic connector present connect directly from laptop using an RJ45 Ethernet cable

     

     

     

140. Select ‘Actions/Autodiag’ tab and search for ‘ Purge'

     

141. Select ‘TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGESearch for routine in ToolboxCoolant Air PurgeThermal / Coolant System - Coolant Purge Starthv / Front Drive Inverter Replacement - Coolant Air Purgehv / Rear Drive Inverter Replacement - Coolant Air Purgehv / Rear Left Drive Inverter Replacement - Coolant Air Purgehv / Rear Right Drive Inverter Replacement - Coolant Air Purgehv / Front Drive Unit Replacement - Coolant Air Purgehv / Rear Drive Unit Replacement - Coolant Air PurgeThermal / Actions - Coolant Purge Stop or Coolant Purge Start ’, click ‘Run’, and allow routine to complete
     Anmerkung

     Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete

     

     

     

142. Remove HSD or RJ45 cable from Ethernet port to disconnect Toolbox 3.0 from vehicle

     

     

143. Inspect coolant level and top off as necessary
     Anmerkung

     Ensure coolant is filled using G-48 coolant

     

144. Install coolant bottle cap

     

145. Install rear apron
     Anmerkung

     14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

     

     

146. Close hood

     

     

147. Raise all four windows
148. Close all four doors
     Anmerkung

     If 12V is powered up, Unlatch rear doors before closing
149. Remove vehicle from lift
     Anmerkung

     Lower rack arms fully and remove from under vehicle

     

150. Schlagen Sie in den Tabellen zur Anforderung der Achsvermessung nach, um zu bestimmen, ob eine EPAS-Ausrichtungsprüfung (EC) oder eine Achsvermessung (AC) erforderlich ist. Sofern durchgeführt, fügen Sie die Ausrichtungsprüfung/Achsvermessung als separate Aktivität hinzu. Siehe Einstellungsbedarf – Aufhängung.