21/08/2024 17:23:52

Rahmen – Rückenlehne – 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen)

Korrekturcode 13081122 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden. HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und darüber, wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

  • 2024-08-15: Added a note for NA vehicles to remind that the seat covers without ISOFIX flag for child locks must be replaced.

Ausbauen

  1. Remove the lower C-pillar trim. See Verkleidung – C-Säule – Unten – LH (7 Sitze) (Ausbauen und Ersetzen).
  2. Fold down the 2nd row LH seatback assembly.
  3. Disconnect the 2nd row LH seat connector.
  4. Move the 2nd row LH seat forward by using s towel bar.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pull up the towel bar with one hand and slide the seat forward with the other hand.
  5. Remove 60 seat rear outboard track fastener
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x patch bolt, 11mm, 37 Nm, Discard after removal
  6. Remove 60 seat rear inboard track fasteners
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x patch bolts, 11mm, 37 Nm, Discard after removal
  7. Move 60 seat fully rearward using towel bar
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    With one hand on towel bar pull up and slide the seat forward with your other hand
  8. Remove 60 seat outboard track cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Slide covers forward to release from 60 seat tracks
  9. Remove center track cover from 2nd row seats
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, Slide covers forward to release from 2nd row seat tracks
  10. Release cabin carpet from 60 seat
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pull cabin carpet towards front of vehicle
  11. Remove 60 seat front inboard track fasteners
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolts, 11mm, 37 Nm, Discard after removal
  12. Remove 2nd row 60 seat frame front outboard track fasteners
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolts, 11mm, 37 Nm, Discard after removal
  13. Remove 2nd row 60 seat assembly from vehicle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Recommend assistance
  14. Remove front push clip from 2nd row 60 cushion assembly outer side shield
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Use pick to remove the push clip from the bottom side of the outboard cover
  15. Remove 2nd row 60 cushion assembly outer side shield
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip 1x connector, Remove outer side shield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection
  16. Remove 2nd row 60 seatback assembly toe kick panel
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove
  17. Release clips and remove inboard outer trim from 2nd row 60 seat cushion assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle
  18. Remove 2nd row 60 seatback panel
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    9x clips, 2x hooks, Release clips starting at the top of back panel working your way down the lower back panel, pull 60 back panel towards front of vehicle to remove
  19. Remove 2nd row center seat switch
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 back panel to ease removal
  20. Remove center back panel from 2nd row center seatback
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x clips, 2 hooks, Lift up at the lower 20 back panel and then slide forward to release
  21. Release 2nd row 60 seat harness connectors and clip from seat frame
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, 7x connectors
  22. Disconnect seat cables from easy entry actuators on 60 seat
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips
  23. Remove cable from 60 fold actuator
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Remove cable from 60 fold actuator
  24. Remove push clips for 2nd row 60 bottom seat pan
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, Remove push clips from front of seat pan
  25. Remove center seatback lumbar bun fastener
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x screw, T20, 1.5 Nm
  26. Remove center seatback lumbar bun
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, Pull bolster outwards to release
  27. Remove center seatback pivot clamps
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove
  28. Remove center seatback from 60 seat frame
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Remove center seatback by lifting upwards
  29. Manually release the center seatback latch
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Use small screwdriver to manipulate the center seatback latch to release
  30. Remove fasteners securing 60 seat pan to seat frame
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame
  31. Remove headrest from 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged
  32. Remove headrest guides from 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides
  33. Remove 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Release clips securing 60 seatback and lift upwards, Seat belt will be removed in a later step
  34. Remove 2nd row 60 seat cushion assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Remove seat bottom by lifting the rear first and removing it towards front of the seat
  35. Remove 2nd row center seat belt anchor
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, T50, 40 Nm, Discard after removal
  36. Remove 2nd row center seat belt guide
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, 2x datums
  37. Remove 2nd row center seat belt from 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pass seat belt through opening
  38. Place 2nd row 60 seatback assembly on a suitable working surface
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Avoid damage to seat cover
  39. Remove easy-entry switch
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, 1x connector
  40. Disconnect seat heating connector
  41. Release 2nd row 60 seatback cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    16x tabs, Pull material downward to release
  42. Remove backrest shell from 2nd row 60 seatback cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Early production models may have staples holding material to shell in some areas
  43. Remove seatback cover from foam
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Nur für NA: Die Sitzbezüge ohne ISOFIX-Schild für Kindersicherungen müssen ausgetauscht werden.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x hogring, Hook & loop attachment around perimeter, Cut hogrings, clean debris

Montieren

  1. Install seatback cover to foam
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x hogrings, Small tie wraps may be used as a substitute, if used trim flush and rotate tie wrap head away from visible surface, Hook & loop around perimeter
  2. Install 2nd row 60 seatback cover to backrest shell
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    16x hooks, Pull material downward to attach, Ensure material is distributed correctly on visible face
  3. Connect the heating pad connector.
  4. Install easy-entry switch
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x tabs, 1x connector
  5. Install 2nd row center seat belt to 2nd row 60 seatback assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Pass seat belt through opening
  6. Install 2nd row center seat belt guide
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, 2x datums
  7. Install 2nd row center seat belt anchor
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, T50, 40 Nm
  8. Place 60 seat pan onto seat frame
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Reinstall seat bottom onto seat frame by starting at the rear of the seat
  9. Secure 60 seat bottom to seat frame
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame
  10. Install 2nd row 60 seatback into place
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back
  11. Install headrest guides into 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Install headrest guides by pressing downwards until lower tab is seated
  12. Install headrest onto 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Push down to secure
  13. Install center seatback pivot clamps
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs
  14. Install center seatback lumbar bun
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips, Press seatback lumbar bun into center frame
  15. Install center seatback lumbar bun fastener
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x screw, T20, 1.5 Nm
  16. Plug in connector and install trim to 60 seat
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.
  17. Install push clip at front of outer 60 side shield assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Install push clip at front bottom side of the trim
  18. Install inboard outer trim to 60 seat
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Clips 3x, Install inboard outer trim and re-seat 3x clips
  19. Insert back panel hooks into center seat back assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks
  20. Install center back panel onto seat back
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x clips
  21. Install 2nd row center seat switch
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, 2x clips
  22. Install 60 toe kick cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    7x clips
  23. Install LH seatback onto 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips
  24. Install 2nd row 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Recommend assistance
  25. Connect 2nd row 60 seat connector
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector
  26. Install fasteners securing 60 seat frame to body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front
  27. Secure cabin carpet to 60 seat
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Strap velcro on
  28. Move 2nd row 60 seatback to vertical position
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Remove seat back protection if necessary
  29. Install 60 seat outboard track cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  30. Install 60 seat outboard track cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  31. Install LH 7s Lower C-Pillar Trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
  32. Re-seat LH rear door seal
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Seat pillar and sill trim tabs underneath seal
  33. Move the both front seats to original position.
  34. Raise all windows and close all doors.