01/03/2023 07:21:52

Sitzschale – Sitz 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen)

Korrekturcode 13050132 0.54 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

Ausbauen

  1. Remove the LH 2nd row seat assembly from the vehicle. See Sitzbaugruppe – 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen).
  2. Remove the push clip from the front of the LH 2nd row seat outer sideshield assembly.
    Tipp: Use a pick to remove the push clip from the bottom side of the outboard cover.
  3. Release the clip that attaches the LH 2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector, and then remove the sideshield from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  4. Release the clips (x3) that attach the LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from the seat assembly.
  5. Remove the LH 2nd row seat toe kick cover. See Abdeckung – Trittschutz – Sitz 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen).
  6. Remove the LH 2nd row seat back panel. See Rückwand – 2. Sitzreihe – LH (Ausbauen und Ersetzen).
  7. Remove the center 2nd row seat back panel. See Rückwand – 2. Sitzreihe – Mitte/20 (5-Sitzer) (Ausbauen und Ersetzen).
  8. Disconnect the LH 2nd row seat harness electrical connectors (x7), and then release the clip that attaches the harness to the seat frame.
  9. Release the seat cables (x4) from the LH 2nd row seat EZ entry actuator.
  10. Release the clip that attaches the cable to the LH 2nd row seat fold actuator.
  11. Remove the push clips (x2) from the LH 2nd row seat cushion pan.
  12. Remove the center 2nd row lumbar bun. See Lendenstützenpolster – 2. Sitzreihe – Mitte/20 (Ausbauen und Ersetzen).
  13. Remove the center 2nd row seat back pivot clamps. See Schwenkschwellen – Rückenlehne – 2. Sitzreihe – Mitte/20 (Ausbauen und Ersetzen).
  14. Lift the center 2nd row seat back upward to remove it from the seat assembly.
  15. Manually release the center seatback latch.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Use a small screwdriver to manipulate the center seatback latch to release it.
  16. Remove the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Tipp: Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • Steckschlüssel, 10 mm
    • Torx-Steckschlüssel T25
  17. Remove the LH 2nd row seat headrest trim. See Kopfstütze – 2. Sitzreihe – Außen – LH (Ausbauen und Ersetzen).
  18. Remove the LH 2nd row headrest adjustment guide. See Einstellführung – Kopfstütze – 2. Sitzreihe (Ausbauen und Ersetzen)
  19. Remove the LH 2nd row seat headrest guide lock. See Führungssperre – Kopfstütze – 2. Sitzreihe (Ausbauen und Ersetzen).
  20. Release the clips (x4) that attach the LH 2nd row seat back to the seat assembly, and then lift the seat back to remove it from the assembly.
  21. Lift the rear of the LH 2nd row seat cushion assembly, and then slide the cushion toward the front of the seat to remove it from the seat assembly.
  22. Disconnect the remaining connectors (x4) from the LH 2nd row seat cushion pan.
  23. Release the J-hooks that attach the LH 2nd row seat cushion cover from the cushion pan, and then remove the cover from the cushion pan.
  24. Disconnect the LH 2nd row seat fold actuator connector.
  25. Disconnect the actuator switch box connector.
  26. Release the remaining seat harness clips (x4) from the LH 2nd row seat cushion pan.
  27. Remove the bolts that attach the LH 2nd row seat fold actuator to the cushion pan, and then remove the actuator from the cushion pan.
    2.5 Nm (1.8 lbs-ft)
    Tipp: Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • Steckschlüssel, 8 mm
  28. Remove the bolts (x6) that attach LH 2nd row seat actuator switch box to the cushion pan, and then remove the switch box, EZ entry latch, and floor latch actuators from the cushion pan.
    2.5 Nm (1.8 lbs-ft)
    Tipp: Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • Steckschlüssel, 8 mm

Montieren

  1. Position the LH 2nd row seat actuator switch box, EZ entry latch, and floor latch actuators to the cushion pan, and then install the bolts (x6) that attach the switch box to the cushion pan.
    2.5 Nm (1.8 lbs-ft)
    Tipp: Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • Steckschlüssel, 8 mm
  2. Position the LH 2nd row seat fold actuator to the cushion pan, and then install the bolts that attach the actuator to the cushion pan.
    2.5 Nm (1.8 lbs-ft)
    Tipp: Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • Steckschlüssel, 8 mm
  3. Secure the seat harness clips (x4) to the LH 2nd row seat cushion pan.
  4. Connect the LH 2nd row seat fold actuator connector.
  5. Connect the actuator switch box connector.
  6. Position the LH 2nd row seat cushion cover onto the cushion pan, and then secure the J-hooks that attach the cover to the cushion pan.
  7. Starting at the rear of the seat, position the LH 2nd row seat pan onto the seat frame.
  8. Install the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    The 10 mm bolts are torqued to 6 Nm. The T25 screws are torqued to 1.5 Nm.
    Tipp: Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • Steckschlüssel, 10 mm
    • Torx-Steckschlüssel T25
  9. Position the LH 2nd row seat back to the seat assembly, and then install the clips (x4) that attach the seat back to the assembly.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure the bottom retainers slide into position.
  10. Install the LH 2nd row seat headrest guide lock. See Führungssperre – Kopfstütze – 2. Sitzreihe (Ausbauen und Ersetzen).
  11. Install the LH 2nd row headrest adjustment guide. See Einstellführung – Kopfstütze – 2. Sitzreihe (Ausbauen und Ersetzen)
  12. Install the LH 2nd row seat headrest trim. See Kopfstütze – 2. Sitzreihe – Außen – LH (Ausbauen und Ersetzen).
  13. Install the center 2nd row seat back pivot clamps. See Schwenkschwellen – Rückenlehne – 2. Sitzreihe – Mitte/20 (Ausbauen und Ersetzen).
  14. Install the center 2nd row lumbar bun. See Lendenstützenpolster – 2. Sitzreihe – Mitte/20 (Ausbauen und Ersetzen).
  15. Position the LH 2nd row seat outer sideshield to the seat assembly, connect the electrical connector, and then secure the clip.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  16. Install the push clip to the front of the LH 2nd row seat outer sideshield assembly.
    Tipp: Use a pick to remove the push clip from the bottom side of the outboard cover.
  17. Install the clips (x3) that attach the LH 2nd row seat inboard outer trim to the LH 2nd row seat.
  18. Install the center 2nd row seat back panel. See Rückwand – 2. Sitzreihe – Mitte/20 (5-Sitzer) (Ausbauen und Ersetzen).
  19. Install the LH 2nd row seat toe kick cover. See Abdeckung – Trittschutz – Sitz 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen).
  20. Install the LH 2nd row seat back panel. See Rückwand – 2. Sitzreihe – LH (Ausbauen und Ersetzen).
  21. Install the LH 2nd row seat assembly. See Sitzbaugruppe – 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen).