23/05/2023 10:59:29

Rahmen – Rückenlehne – 2. Sitzreihe – RH (7-Sitzer) (Ausbauen und Ersetzen)

Korrekturcode 13081022 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden. HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und darüber, wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

Ausbauen

  1. Open the RH front and both rear doors.
  2. Lower the RH front and both rear windows.
  3. Move the RH 2nd row seat forward using the towel bar.
  4. Remove the RH 2nd row back panel. See Rückwand – 2. Sitzreihe – RH (Ausbauen und Ersetzen).
  5. Remove the RH 2nd row seat should switch. See Schulterschalter – Rückenlehne – 2. Sitzreihe – LH (Ausbauen und Ersetzen).
  6. Remove the RH 2nd row seat toe kick cover. See Abdeckung – Trittschutz – Sitz 2. Sitzreihe – RH (7-Sitzer) (Ausbauen und Ersetzen).
  7. Remove the clips (x2) and elastic harness holder that attach the seat harness to the bottom side of the seat frame, and then disconnect the 2nd row seat connector.
  8. Remove the RH 2nd row headrest. See Kopfstütze – 2. Sitzreihe – Außen – LH (Ausbauen und Ersetzen).
  9. Remove the RH 2nd row headrest adjustment guide and guide lock. See:
  10. Release the clips (x4) that attach the RH 2nd row seat back assembly to the vehicle, and then lift the seat back upward to remove it from the vehicle.
  11. Place the RH 2nd row seat back assembly on a suitable working surface.
  12. Disconnect the seat heating connector.
  13. Release the tabs (x16) that attach the RH 2nd row seat back cover to the seat back assembly.
  14. Remove the back rest shell from the RH 2nd row seat back cover.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Early production vehicles may have staples holding the material to the shell in some areas.
  15. Release the hook and loop attachment around the perimeter, cut and discard the hog rings (x3), and then remove the RH 2nd row seat back cover from the foam.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Clean any remaining debris from the assembly.

Montieren

  1. Position the RH 2nd row seat back cover onto the foam, and then install the hog rings (x3) and secure the hook and loop around the perimeter.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Small cable ties may be used as a substitute for the hog rings. If cable ties are used, trim the excess cable flush, and then rotate the head away from the visible areas.
  2. Position the seat back shell into the RH 2nd row seat back cover, and then secure the tabs (x16) that attach the cover to the seat back shell.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure the cover is evenly distributed on the front of the back rest.
  3. Connect the seat heating connector.
  4. Position the RH 2nd row seat back cover into the vehicle, and then install the seat back assembly into the seat assembly.
  5. Install the RH 2nd row headrest adjustment guide and guide lock. See:
  6. Install the RH 2nd row headrest. See Kopfstütze – 2. Sitzreihe – Außen – LH (Ausbauen und Ersetzen).
  7. Connect the 2nd row seat harness connector, and then secure the clips (x2) and elastic harness holder that attach the seat harness to the bottom side of the seat frame.
  8. Install the RH 2nd row seat toe kick cover. See Abdeckung – Trittschutz – Sitz 2. Sitzreihe – RH (7-Sitzer) (Ausbauen und Ersetzen).
  9. Install the RH 2nd row seat should switch. See Schulterschalter – Rückenlehne – 2. Sitzreihe – LH (Ausbauen und Ersetzen).
  10. Install the RH 2nd row back panel. See Rückwand – 2. Sitzreihe – RH (Ausbauen und Ersetzen).
  11. Move the RH 2nd row seat back to the vertical position.
  12. Move the front passenger seat to the original position.
  13. Raise the RH front and rear windows.
  14. Close the RH front and rear doors