2026-08-25

Tie Rod - Inner - LH (Remove and Replace)

Korrekturcode 32013202 32013302 FRT 0.48 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und seine zugehörige FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden. HINWEIS: Weitere Informationen über FRTs und darüber, wie sie erstellt werden, finden Sie unter Richtzeiten. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen. HINWEIS: Siehe Maßnahmen zur Ergonomie für sichere und gesunde Arbeitsmethoden.

Warnung
Dieses Verfahren ist ein ENTWURF. Es wurde zwar validiert, jedoch können Sicherheitshinweise und Vorsichtsmaßnahmen fehlen. Befolgen Sie die Sicherheitshinweise, und gehen Sie beim Arbeiten an oder in der Nähe von Hochspannungssystemen und -bauteilen äußerst vorsichtig vor.
  • 2025-12-16: Released new procedure.

Entfernen

  1. Remove the LH front wheel arch liner. See Radhausverkleidung – Vorne – LH (Nicht Strukturpack)(Ausbauen und Ersetzen) or Radhausverkleidung – Vorne – LH (Strukturpack) (Ausbauen und Ersetzen).
  2. Remove LH outer tie rod from knuckle
    Anmerkung
    1x nyloc nut, 22mm, 180 Nm, Discard after removal
  3. Remove LH tie rod end from knuckle
  4. Remove large bellows clamp from bellows
    Anmerkung
    1x clamp, Discard after removal
  5. Remove bellows seal clip from bellows
    Anmerkung
    1x clip
  6. Slide bellows toward LH outer tie rod end
    Anmerkung
    You need to access the LH inner tie rod end inner ball joint
  7. Remove LH tie rod assembly from pinion housing
    Anmerkung
    1x inner tie rod, 38mm crowfoot, 88 Nm, Twist until it comes off

Montieren

  1. Adjusting new tie rod length to match old tie rod before installation
    Anmerkung
    1x jam nut, 21mm, 14mm, Turn adjust inner tie rod as needed, Parts line up is to count the threads on the removed tie rod then adjust to the same count on the new one, This will make alignment adjustment easier
  2. Install LH inner tie rod assembly onto pinion housing
    Anmerkung
    1x inner tie rod, 38 crowfoot, 88 Nm, Twist until it's fully seated
  3. Slide bellows into clamping position
    Anmerkung
    Slide bellows over pinion housing in preparation for clamping
  4. Secure large bellows clamp onto bellows
    Anmerkung
    1x clamp
  5. Secure bellows seal clip onto bellows
    Anmerkung
    1x clamp
  6. Position LH tie rod end to LH front knuckle
  7. Install nut securing the LH tie rod end to the knuckle
    Anmerkung
    1x nyloc nut, 22mm, 180 Nm, Install new nyloc nut
  8. Install the LH front wheel arch liner. See Radhausverkleidung – Vorne – LH (Nicht Strukturpack)(Ausbauen und Ersetzen) or Radhausverkleidung – Vorne – LH (Strukturpack) (Ausbauen und Ersetzen).
  9. Review wheel alignment requirements and add correction code as needed. See Einstellungsbedarf – Aufhängung.