03/06/2024 17:24:47
Bremsleitungen – Schweller LH (Strukturpack) (Ausbauen und Ersetzen)
Korrekturcode 33035112 1.86 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.
- 2023-12-08: Updated brake stiffness routine.
Warnung
Bei diesem Verfahren handelt es sich um einen ENTWURF, der jedoch bereits validiert wurde. Warn- und Sicherheitshinweise sind möglicherweise nicht vorhanden. Befolgen Sie die Sicherheitshinweise, und gehen Sie beim Arbeiten an oder in der Nähe von Hochspannungssystemen und -bauteilen äußerst vorsichtig vor. Übermitteln Sie Verbesserungsvorschläge und Feedback an ServiceDevelopment@teslamotors.com.
Ausbauen
- Remove the LH rocker panel carrier. See Träger – Trittbrett – LH (Strukturpack) (Ausbauen und Ersetzen).
-
Remove butyl patches covering LH rocker access holes
Anmerkung2x butyl patches, Clean excess butyl from area
-
Install lift pad adapters onto LH rocker
Anmerkung2x lift pad adapters
- Remove the RH rocker panel carrier. See Träger – Trittbrett – LH (Strukturpack) (Ausbauen und Ersetzen).
-
Remove butyl patches covering RH rocker access holes
Anmerkung2x butyl patches, Clean excess butyl from area
-
Install lift pad adapters onto RH rocker
Anmerkung2x lift pad adapters
-
Raise and support vehicle
AnmerkungVerify jack locations prior to lifting vehicle, ONLY place on lifting points at front and rear of rocker panels
- Open LH front door
- Lower LH front window
- Remove the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
-
Remove bolt securing frunk to washer fluid reservoir neck
Anmerkung1x bolt, 10mm, 5 Nm
-
Release washer tank neck from washer tank and set aside
Anmerkung1x O-ring, No need to remove hose from neck
-
Remove HEPA filter assembly
Anmerkung2x bolts, 10mm, 5 Nm, Pivot rearward edge up and past brake reservoir, then lift up to clear frunk assembly
-
Power off vehicle from center display
AnmerkungVia Controls > Safety > Power Off, Select Power Off button at warning dialogue box
-
Disconnect LV battery connector and First Responder Loop
Anmerkung2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
- Remove all four wheels. See Radbaugruppe (Aus- und Einbauen).
-
Release LH front wheel liner from HV battery
Anmerkung1x clip, 1x bolt, 10mm, 5 Nm
- Remove the LH front fender garnish. See Verzierung – Kotflügel – Vorn – Links (Ausbauen und Ersetzen).
- Remove the LH front wheel arch liner. See Radhausverkleidung – Vorne – LH (Strukturpack) (Ausbauen und Ersetzen).
- Remove the LH rear wheel arch liner. See Radhausverkleidung – Hinten – LH (Strukturpack) (Ausbauen und Ersetzen).
-
Release clipping points securing compressor HV harness to front of vehicle body
Anmerkung5x clips, Take note of original routing
-
Release clipping points securing compressor HV harness to side of vehicle body
Anmerkung8x clips, Release all clipping points
-
Release side sill brake pipe assembly from LH front junction block
Anmerkung2x nuts, 12mm, 16 Nm, Front brake pipe B and C bundle does not detach from junction block
-
Release rear brake lines from LH rear junction block
Anmerkung2x nuts, 12mm, 16 Nm, Side sill brake pipe assembly does not detach from junction block
-
Remove bolt securing LH rear junction block to body
Anmerkung1x bolt, 10mm, 6 Nm
-
Release side sill brake pipe assembly from clips
Anmerkung7x clips, Do not bend pipe
-
Remove side sill brake pipe assembly
Anmerkung1x stud, Release LH rear junction block from body stud then remove assembly from front wheel well
Montieren
-
Position side sill brake pipe assembly
Anmerkung1x stud, Position assembly onto front wheel well then secure LH rear junction block onto body stud
-
Secure side sill brake pipe assembly onto clips
Anmerkung7x clips, Do not bend pipe, Start with front clip and align pipes with LH front junction block
-
Install bolt securing LH rear junction block to body
Anmerkung1x bolt, 10mm, 6 Nm
-
Secure rear brake lines onto LH rear junction block
Anmerkung2x nuts, 12mm, 16 Nm, Side sill brake pipe assembly does not detach from junction block
-
Secure side sill brake pipe assembly onto LH front junction block
Anmerkung2x nuts, 12mm, 16 Nm, Front brake pipe B and C bundle does not detach from junction block
-
Install clipping points securing compressor HV harness to side of vehicle body
Anmerkung8x clips, Fully secure all clips and route harness as needed
-
Install clipping points securing compressor HV harness to front of vehicle body
Anmerkung5x clips, Return to original routing, Verify fully secured
-
Lower vehicle for access to underhood area
AnmerkungMake sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
-
Connect first responder loop and LV battery
Anmerkung2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
-
Fill brake bleeder reservoir to full level
-
Clean area around brake fluid reservoir and remove brake reservoir cap
-
Top off brake fluid reservoir
AnmerkungTop off brake fluid as needed
-
Install pressure bleeder adapter onto reservoir
-
Set brake bleed reservoir pressure to 30 psi
AnmerkungConnect power supply to bleeder and turn on the power, Set pressure to 30 psi, Attach brake bleed reservoir to brake bleed adapter
-
Connect to vehicle using Toolbox 3.0
AnmerkungVehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle. https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)
- Select Actions/Autodiag and search for "bleed"
-
Remove bleeding valve covers and install the fluid catching bottle to LH front brake caliper outer bleeding valve before starting the ESP
Anmerkung2x covers
-
Open LH front brake caliper outer
bleeding valve then click the play button next to "PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDSearch for routine in ToolboxFL and RR brake bleed procedureChassis / Brakes - Brake Bleed FL-RRChassis / Brakes - Brake Bleed FL-RR" and select Run to start the ESP, then close
the bleeding valve once the pump stop running, then repeat the process for inner bleeding
valve, and then lastly repeat the process for outer bleeding valve again
Anmerkung2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
-
Repeat the above step till clear fluid and no air bubbles come out of the LH front brake caliper bleeding valve
Anmerkung2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
-
Remove the fluid catching bottle, Torque LH front brake caliper bleeding valves then install covers
Anmerkung2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
-
Remove bleeding valve covers and install the fluid catching bottle to RH front brake caliper outer bleeding valve before starting the ESP
Anmerkung2x covers
-
Open RH front brake caliper outer
bleeding valve then Click the play button next to "PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDSearch for routine in ToolboxFR and RL brake bleed procedureChassis / Brakes - Brake Bleed FR-RLChassis / Brakes - Brake Bleed FR-RL" and select Run to start the ESP, then close
the bleeding valve once the pump stop running, then repeat the process for inner bleeding
valve, and then lastly repeat the process for outer bleeding valve again
Anmerkung2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
-
Repeat the above step till clear fluid and no air bubbles come out of the RH front brake caliper bleeding valves
Anmerkung2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
-
Remove the fluid catching bottle, Torque RH front brake caliper bleeding valves and install covers
Anmerkung2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
-
Remove bleeding valve cover and install the fluid catching bottle to RH rear brake caliper bleeding valve before starting the ESP
Anmerkung1x cover
-
Open RH rear brake caliper bleeding
valve then Click the play button next to "PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDSearch for routine in ToolboxFL and RR brake bleed procedureChassis / Brakes - Brake Bleed FL-RRChassis / Brakes - Brake Bleed FL-RR" and select Run to start the ESP, then close
the bleeding valve once the pump stop running
Anmerkung1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
-
Repeat the above step till clear fluid and no air bubbles come out of the RH rear brake caliper bleeding valve
Anmerkung1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
-
Remove the fluid catching bottle, Torque RH rear brake caliper bleeding valve and install cover
Anmerkung1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
-
Remove bleeding valve cover and install the fluid catching bottle to LH rear brake caliper bleeding valve before starting the ESP
Anmerkung1x cover
-
Open LH rear brake caliper bleeding
valve then Click the play button next to "PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDSearch for routine in ToolboxFR and RL brake bleed procedureChassis / Brakes - Brake Bleed FR-RLChassis / Brakes - Brake Bleed FR-RL" and select Run to start the ESP, then close
the bleeding valve once the pump stop running
Anmerkung1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
-
Repeat the above step untill clear fluid and no air bubbles come out of the LH rear brake caliper bleeding valve
Anmerkung1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
-
Remove the fluid catching bottle, Torque LH rear brake caliper bleeding valve and install cover
Anmerkung1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
-
Power off brake bleed reservoir and detach brake bleed reservoir from brake bleed adapter
-
Remove pressure bleeder adapter from reservoir
-
Check fluid level
AnmerkungTop off if necessary
-
Install brake reservoir cap
- Pump the brake pedal a few times to ensure the brake pedal feels normal
-
Mit Toolbox 3.
- Remove ethernet cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
-
Raise vehicle partially and lower lift onto locks
AnmerkungSet vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
- Install the LH rear wheel arch liner. See Radhausverkleidung – Hinten – LH (Strukturpack) (Ausbauen und Ersetzen).
- Install the LH front wheel arch liner. See Radhausverkleidung – Vorne – LH (Strukturpack) (Ausbauen und Ersetzen).
- Install all four wheels. See Radbaugruppe (Aus- und Einbauen).
-
Install HEPA filter assembly
Anmerkung2x bolts, 10mm, 5 Nm, Pivot forward edge down past frunk assembly, then carefully move rear edge past brake reservoir and into position
-
Install washer tank neck to washer tank
Anmerkung1x O-ring, Ensure washer hose is properly routed after installation
-
Secure frunk to washer fluid reservoir neck
Anmerkung1x bolt, 10mm, 5 Nm
- Install the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
-
Remove vehicle from lift
AnmerkungLower rack arms fully and remove from under vehicle
- Raise LH front window
- Close LH front door
-
Remove lift pad adapters from LH rocker
Anmerkung2x lift pad adapters
-
Install butyl patches onto LH rocker access holes
Anmerkung2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"
- Remove the LH rocker panel carrier. See Träger – Trittbrett – LH (Strukturpack) (Ausbauen und Ersetzen).
-
Remove lift pad adapters from RH rocker
Anmerkung2x lift pad adapters
-
Install butyl patches onto RH rocker access holes
Anmerkung2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"
- Install the RH rocker panel carrier. See Träger – Trittbrett – LH (Strukturpack) (Ausbauen und Ersetzen).