16/12/2022 05:51:34
Schaumstoff – Sitzkissen – Sitz 2. Sitzreihe – LH (7-Sitzer) (Ausbauen und Ersetzen)
Korrekturcode 13089502 0.96 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.
Warnung
Bei diesem Verfahren handelt es sich um einen ENTWURF, der jedoch bereits validiert wurde. Warn- und Sicherheitshinweise sind möglicherweise nicht vorhanden. Befolgen Sie die Sicherheitshinweise, und gehen Sie beim Arbeiten an oder in der Nähe von Hochspannungssystemen und -bauteilen äußerst vorsichtig vor. Übermitteln Sie Verbesserungsvorschläge und Feedback an ServiceDevelopment@teslamotors.com.
- Open all four doors
- Lower all four windows
- Move LH front seat forward
- Move RH front seat forward
-
Partially remove LH rear door seal
-
Remove LH 7s Lower C-Pillar Trim
Anmerkung8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
-
Fold 60 seat into down position
-
Disconnect logic connector at LH seat frame
Anmerkung1x connector
-
Move 60 seat forward using towel bar
AnmerkungWith one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove 60 seat rear outboard track fastener
Anmerkung1x patch bolt, 11mm, 37 Nm, Discard after removal
-
Remove 60 seat rear inboard track fasteners
Anmerkung2x patch bolts, 11mm, 37 Nm, Discard after removal
-
Move 60 seat fully rearward using towel bar
AnmerkungWith one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove 60 seat outboard track cover
Anmerkung1x clip, Slide covers forward to release from 60 seat tracks
-
Remove center track cover from 2nd row seats
Anmerkung2x clips, Slide covers forward to release from 2nd row seat tracks
-
Release cabin carpet from 60 seat
AnmerkungPull cabin carpet towards front of vehicle
-
Remove 60 seat front inboard track fasteners
Anmerkung1x bolts, 11mm, 37 Nm, Discard after removal
-
Remove 60 seat front outboard track fasteners
Anmerkung1x bolts, 11mm, 37 Nm, Discard after removal
-
Remove 2nd row 60 seat assembly from vehicle
AnmerkungRecommend assistance
-
Remove front push clip from 60 outer sideshield assembly
Anmerkung1x clip, Use pick to remove the push clip from the bottom side of the outboard cover
-
Remove 60 outer sideshield assembly
Anmerkung1x clip 1x connector, Remove outer sideshield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection
-
Release clips and remove inboard outer trim from 60 seat
Anmerkung3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle
-
Remove 60 seat toe kick cover
Anmerkung7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove
-
Remove 60 seatback panel
Anmerkung9x clips, 2x hooks, Release clips starting at the top of backpanel working your way down the lower backpanel, pull 60 backpanel towards front of vehicle to remove
-
Remove 2nd row center seat switch
Anmerkung1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 backpanel to ease removal
-
Remove center backpanel from center seatback
Anmerkung5x clips, 2 hooks, Lift up at the lower 20 backpanel and then slide forward to release
-
Release 60 seat harness connectors and clip from seat from seat frame
Anmerkung1x clip, 7x connectors
-
Disconnect seat cables from easy entry actuators on 60 seat
Anmerkung4x clips
-
Remove push clips for 60 bottom seat pan
Anmerkung2x clips, Remove push clips from front of seat pan
-
Remove center seatback lumbar bun fastener
Anmerkung1x screw, T20, 1.5 Nm
-
Remove center seatback lumbar bun
Anmerkung2x clips, Pull bolster outwards to release
-
Remove center seatback pivot clamps
Anmerkung2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove
-
Remove center seatback from 60 seat frame
AnmerkungRemove center seatback by lifting upwards
-
Manually release the center seatback latch
AnmerkungUse small screwdriver to manipulate the center seatback latch to release
-
Remove fasteners securing 60 seat pan to seat frame
Anmerkung4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame
-
Remove headrest from 60 seat assembly
AnmerkungSimultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged
-
Remove headrest guides from 60 seat
AnmerkungPull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides
-
Remove 60 seatback
Anmerkung4x clips, Release clips securing 60 seatback and lift upwards
-
Remove 60 seat bottom
AnmerkungRemove seat bottom by lifting the rear first and removing it towards front of the seat
-
Remove remaining connections from 60 seat pan
Anmerkung4x connections, Remove remaining connections to 60 seat cushion
-
Remove seat cover from 60 seat pan
AnmerkungRemove 60 seat cover from perimeter of seat pan by releasing J-hooks around the perimeter of the seat
-
Remove 60 seat cushion from seat cover
Anmerkung6x hog ring, Cut the hog rings holding the seat cover to seat cushion and remove seat cover
-
Install seat cover on cushion
Anmerkung6x hog ring, Place seat cover on new cushion and attach with 6x hog rings, ensure the hog rings go through the seat in the intended areas
-
Install 60 seat pan onto seat cushion
AnmerkungPlace seat pan onto seat cushion and cover, Secure seat cover to pan by hooking the J-hooks around the perimeter of the seat
-
Install 60 under-seat harness
Anmerkung4x clips
-
Place 60 seat pan onto seat frame
AnmerkungReinstall seat bottom onto seat frame by starting at the rear of the seat
-
Secure 60 seat bottom to seat frame
Anmerkung4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame
-
Install 60 seat back into place
Anmerkung4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back
-
Install headrest guides into 60 seat assembly
AnmerkungInstall headrest guides by pressing downwards until lower tab is seated
-
Install headrest onto 60 seat assembly
AnmerkungPush down to secure
-
Install center seatback pivot clamps
Anmerkung2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs
-
Install center seatback lumbar bun
Anmerkung2x clips, Press seatback lumbar bun into center frame
-
Install center seatback lumbar bun fastener
Anmerkung1x screw, T20, 1.5 Nm
-
Plug in connector and install trim to 60 seat
Anmerkung1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.
-
Install push clip at front of outer 60 sideshield assembly
Anmerkung1x clip, Install push clip at front bottom side of the trim
-
Install inboard outer trim to 60 seat
AnmerkungClips 3x, Install inboard outer trim and reseat 3x clips
-
Insert backpanel hooks into center seat back assembly
Anmerkung2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks
-
Install center backpanel onto seat back
Anmerkung5x clips
-
Install 2nd row center seat switch
Anmerkung1x connector, 2x clips
-
Install 60 toe kick cover
Anmerkung7x clips
-
Install LH seatback onto 60 seat assembly
Anmerkung9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips
-
Install 2nd row 60 seat assembly
AnmerkungRecommend assistance
-
Connect logic connector at LH 60 seat frame
Anmerkung1x connector
-
Install fasteners securing 60 seat frame to body
Anmerkung5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front
-
Secure cabin carpet to 60 seat
AnmerkungStrap velcro on
-
Fold the 60 seat into vertical position
AnmerkungRemove seat back protection if necessary
-
Install 60 seat outboard track cover
Anmerkung1x clip
-
Install 60 seat outboard track cover
Anmerkung1x clip
-
Install LH 7s Lower C-Pillar Trim
Anmerkung8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim
-
Reseat LH rear door seal
AnmerkungSeat pillar and sill trim tabs underneath seal
- Move RH front seat to original position
- Move LH front seat to original position
- Raise all four windows
-
Close all four doors
AnmerkungIf 12V is powered up, Unlatch rear doors before closing