08/04/2024 11:00:30

Event Data Recorder Retrieval

Korrekturcode NA

Warning IconA warning icon, calling your attention to a possibly risky situation
Warnung
Bei diesem Verfahren handelt es sich um einen ENTWURF, der jedoch bereits validiert wurde. Warn- und Sicherheitshinweise sind möglicherweise nicht vorhanden. Befolgen Sie die Sicherheitshinweise, und gehen Sie beim Arbeiten an oder in der Nähe von Hochspannungssystemen und -bauteilen äußerst vorsichtig vor. Übermitteln Sie Verbesserungsvorschläge und Feedback an ServiceDevelopment@teslamotors.com.
Informational PurposesAn informational icon, calling your attention
Anmerkung
Refer to CD-20-20-001 for Model Y Event Data Recorder (EDR) guide.
Informational PurposesAn informational icon, calling your attention
Anmerkung
Use the following procedure(s) for Model Y Non-Structural Pack EDR retrieval as required:
Informational PurposesAn informational icon, calling your attention
Anmerkung
Use the following procedure(s) for Model Y Structural Pack EDR retrieval as required:

Establish a Direct-to-Module Connection (Non-Structural Pack)

  1. Open all of the doors.
  2. Lower all of the windows.
  3. On the vehicle touchscreen, select the Tesla symbol, and then confirm and note the vehicle’s firmware version.
    Abbildung 1. Model 3 shown; Model Y similar
  4. Remove the Restraint Control Module (RCM). See Steuergerät – Rückhaltesystem (Nicht Strukturpack) (Ausbauen und Ersetzen).
  5. Connect the EDR extraction harness connectors (x2) to the RCM.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • EDR extraction harness, RCM, Bosch MS-M3-MY - 1492139-00-B
  6. Connect the EDR extraction harness connector to the PCAN USB to CAN adapter connector.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • PCAN USB to CAN adapter - 1016990-00-A
  7. Connect the PCAN USB to CAN adapter dongle connector to the laptop USB port.
  8. Connect the XP-20 (heavy duty) jump start 12V power to the EDR extraction harness.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Jump start, XP-20 (heavy duty) - 1016990-00-A
  9. Open the Tesla EDR Retrieval Program.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    The program will automatically try to connect to RCM and will display a green circle in the lower left corner when connected.
  10. Once the Tesla EDR Retrieval Program connection is established, click "Run EDR Retrieval", and then follow the on-screen prompts to retrieve and save the EDR data.
  11. Use the retrieved data to "Generate a Report". See https://edr.tesla.com.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    EDR retrieval time will vary based on the user and retrieved data.
  12. Close the Tesla EDR Retrieval Program.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Select "X" at the top right of the window to close the program once EDR retrieval is complete.
  13. Disconnect the XP-20 (heavy duty) jump start 12V power from the EDR extraction harness.
  14. Disconnect the PCAN USB to CAN adapter dongle connector from the laptop USB port.
  15. Disconnect the EDR extraction harness connector from the PCAN USB to CAN adapter connector.
  16. Disconnect the EDR extraction harness connectors (x2) from the RCM.
  17. Install the RCM. See Steuergerät – Rückhaltesystem (Nicht Strukturpack) (Ausbauen und Ersetzen).
  18. Raise all of the windows.
  19. Close all of the doors.

Establish a Direct-to-Module Connection (Structural Pack)

  1. Remove the RCM. See Steuergerät – Rückhaltesystem (Strukturpack) (Ausbauen und Ersetzen).
  2. Connect the EDR extraction harness connectors (x2) to the RCM.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • EDR extraction harness, RCM, Bosch MS-M3-MY - 1492139-00-B
  3. Connect the EDR extraction harness connector to the PCAN USB to CAN adapter connector.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Es wird empfohlen, die folgenden Werkzeuge zu verwenden:
    • PCAN USB to CAN adapter - 1016990-00-A
  4. Connect the PCAN USB to CAN adapter dongle connector to the laptop USB port.
  5. Connect the XP-20 (heavy duty) jump start 12V power to the EDR extraction harness.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Jump start, XP-20 (heavy duty) - 1016990-00-A
  6. Open the Tesla EDR Retrieval Program.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    The program will automatically try to connect to RCM and will display a green circle in the lower left corner when connected.
  7. Once the Tesla EDR Retrieval Program connection is established, click "Run EDR Retrieval", and then follow the on-screen prompts to retrieve and save the EDR data.
  8. Use the retrieved data to "Generate a Report". See https://edr.tesla.com.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    EDR retrieval time will vary based on the user and retrieved data.
  9. Close the Tesla EDR Retrieval Program.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Select "X" at the top right of the window to close the program once EDR retrieval is complete.
  10. Disconnect the XP-20 (heavy duty) jump start 12V power from the EDR extraction harness.
  11. Disconnect the PCAN USB to CAN adapter dongle connector from the laptop USB port.
  12. Disconnect the EDR extraction harness connector from the PCAN USB to CAN adapter connector.
  13. Disconnect the EDR extraction harness connectors (x2) from the RCM.
  14. Install the RCM. See Steuergerät – Rückhaltesystem (Strukturpack) (Ausbauen und Ersetzen).