03/06/2024 17:24:58

Bremsleitungen – Vorderes Bündel (Strukturpack) (Ausbauen und Ersetzen)

Korrekturcode 33035012 3.60 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

  • 2023-12-06: Updated brake stiffness routine.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warnung
Bei diesem Verfahren handelt es sich um einen ENTWURF, der jedoch bereits validiert wurde. Warn- und Sicherheitshinweise sind möglicherweise nicht vorhanden. Befolgen Sie die Sicherheitshinweise, und gehen Sie beim Arbeiten an oder in der Nähe von Hochspannungssystemen und -bauteilen äußerst vorsichtig vor. Übermitteln Sie Verbesserungsvorschläge und Feedback an ServiceDevelopment@teslamotors.com.
  1. Raise and support vehicle with wheels still touching the ground
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Ensure vehicle is not charging
  2. Open the LH front door and lower the LH front window.
  3. Remove the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
  4. Remove the underhood storage unit. See Frontstauraum (Ausbauen und Ersetzen).
  5. Remove the HEPA filter. See Baugruppe – Filter – HEPA (Ausbauen und Ersetzen).
  6. Remove the HEPA duct. See Kanal – HEPA (Ausbauen und Ersetzen)
  7. Disconnect LV power. See 12-V-/Niederspannungsversorgung (Trennen und Verbinden).
  8. Verify operation of multimeter
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing LV battery, Touch lightly and do not damage terminals
  9. Remove clip securing negative terminal cable to AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  10. Remove negative terminal cable from body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 10 Nm
  11. Remove the LV battery. See 12-V-/LV-Batterie (Ausbauen und Ersetzen).
  12. Remove all four wheels. See Radbaugruppe (Aus- und Einbauen).
  13. Remove the mid aero shield panel. See Verkleidung – Windabweiser – Mitte (Ausbauen und Ersetzen).
  14. Remove all items from pockets and ensure not wearing metal items
  15. Inspect HV insulating gloves
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves. https://service.teslamotors.com/protected-doc/ServiceBulletins/External/TN/TN-15-92-003_High_Voltage_Awareness_Care_Points_R4.pdf
  16. Put on HV insulating gloves and leather over gloves
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure to wear Electrical Protective Gloves any time Hioki tester is used
  17. Install amp clamp to RDU HV harness
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as required If current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.
  18. Release RDU HV harness from HV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, Release locking tab and rotate the release lever up to disengage the connector, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damaged
  19. Verify no high voltage at RDU HV header
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering
  20. Remove front aero shield
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    12x bolts, 10mm, 6 Nm, 2x nuts, 15mm, 6 Nm, 2x clips, 2x hooks
  21. Release LH and RH front wheel liner from HV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x rocker bolt, 10mm, 12 Nm, 2x aero shield bolts, 10mm, 6 Nm
  22. Release clipping points securing compressor HV harness to front of vehicle body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x clips, Take note of original routing
  23. Remove the LH and RH front wheel arch liners. See Radhausverkleidung – Vorne – LH (Strukturpack) (Ausbauen und Ersetzen).
  24. Lower vehicle for access to underhood area
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  25. Position the oil drain container under hydraulic control unit area
  26. Position protective fender cover over fan shroud and support
  27. Remove clips securing PT supply hose to AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips
  28. Release clip securing HV compressor harness to plastic connector housing
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Take note of original routing
  29. Release clip securing AC compressor logic connector to HV harness
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x fir tree clip
  30. Release AC compressor logic connector
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x locking connector, Pull red tab to disengage lock and pull again to release connector, Do not push down on red tab
  31. Remove fastener securing compressor HV harness to AC compressor
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 13mm, 9 Nm
  32. Release HV harness connector from AC compressor
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x locking connector, Disengage black locking tab and release connector
  33. Remove AC compressor ground strap
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 7 Nm, MYSP uses T25 bolt
  34. Remove the clip securing the coolant hose to the AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x fir tree clip
  35. Remove AC compressor and AC compressor bracket assembly from strut tower support brace
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 15mm, 31 Nm, Recommend assistance, Support the AC compressor while removing the fasteners, Carefully remove the AC compressor and AC compressor bracket towards the front of the vehicle, under the strut tower support brace and rest on fender cover
  36. Release positive terminal cover
  37. Remove positive terminal cable from cowl
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x stud, E5, 8 Nm
  38. Release 12V positive cable clip from front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  39. Disconnect the supermanifold harness from the front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector
  40. Remove bolts securing front controller shield assembly and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 10mm, 8.5 Nm
  41. Disconnect remaining connectors on front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x connectors, Release locking tabs first if equipped
  42. Release harness guide from front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x patch bolts, 8mm, 6 Nm, 1x temp set clip, Discard bolts after removal, Remove bolts first, then pivot harness guide slightly forward and up to remove temp set clip from front harness
  43. Remove bolts securing front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x bolts, 10mm, 10 Nm
  44. Remove front controller upper ground strap from body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 10 Nm, Located under cowl, Discard bolt after removal
  45. Remove front controller lower ground strap
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 10 Nm
  46. Remove the front controller from vehicle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Push harness connectors down to provide space, Gently pry bottom of controller out of BIW temp set holes, Then swing controller forward and up to release from top temp set
  47. Disconnect HCU connector
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, Release red locking tab, Press black release tab and rotate lever upward to remove
  48. Release HCU connector harness
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips
  49. Remove bolt securing the steering gear assembly to intermediate shaft assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 13mm, 18 Nm
  50. Slide the electric steering column upward to remove it from the steering gear assembly
  51. Loosen bolts securing shock tower brace to RH shock tower
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 15mm, 67 Nm, 1x bolt, 15mm, 62 Nm, See image for torque location
  52. Remove fasteners for LH side of shock tower brace
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 15mm, 67 Nm, 1x bolt, 15mm, 62 Nm
  53. Remove 4-tube bundle brake lines from HCU
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x nuts, 12mm, 16 Nm
  54. Release 4-tube bundle brake lines from LH top spacer
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Do not bend pipes
  55. Release 4-tube bundle brake lines from LH bottom spacer
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Do not bend pipe
  56. Release front brake pipe A from RH jounce hose
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x nut, 12mm, 16 Nm
  57. Release front brake pipe A from clips
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x clips, Do not bend pipe
  58. Remove front brake pipe A
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not bend pipe, Four-step removal, Remove pipe from HCU and negotiate around steering column, Guide pipe through RH wheel well, Lift LH side of thermal bar and guide pipe over body, Negotiate pipe around RH side of FDU and around HVAC line
  59. Release side sill brake pipe assembly from LH front junction block
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x nuts, 12mm, 16 Nm, Front brake pipe B and C bundle does not detach from junction block
  60. Remove bolt securing LH junction block to body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 6 Nm
  61. Remove front brake pipe B and C bundle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x stud, Do not bend pipe, Three-step removal, Release junction block from rear brake pipes and body stud simultaneously, Remove bundle from HCU, Guide bundle toward front of vehicle
  62. Release front brake pipe D from LH jounce hose
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x nut, 12mm, 16 Nm
  63. Release front brake pipe D from clip
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Do not bend pipe
  64. Remove front brake pipe D
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not bend pipe, Remove pipe from HCU then guide through LH wheel well
  65. Position front brake pipe D
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not bend pipe, Guide pipe through LH wheel well then position onto HCU
  66. Secure front brake pipe D onto clip
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Do not bend pipe
  67. Secure front brake pipe D onto LH jounce hose
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x nut, 12mm, 16 Nm
  68. Position front brake pipe B and C bundle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x stud, Do not bend pipe, Three-step installation, Guide bundle toward rear of vehicle, Position bundle onto HCU, Secure junction block onto rear brake pipes and body stud simultaneously
  69. Install bolt securing LH junction block to body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 6 Nm
  70. Secure side sill brake pipe assembly onto LH front junction block
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x nuts, 12mm, 16 Nm, Front brake pipe B and C bundle does not detach from junction block
  71. Position front brake pipe A
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not bend pipe, Four-step installation, Negotiate pipe around HVAC line and around RH side of FDU, Lift LH side of thermal bar and guide pipe under bar, Guide pipe through RH wheel well, Negotiate around steering column and position pipe onto HCU
  72. Secure front brake pipe A onto clips
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x clips, Do not bend pipe
  73. Secure front brake pipe A onto RH jounce hose
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x nut, 12mm, 16 Nm
  74. Secure 4-tube bundle brake lines onto LH bottom spacer
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Do not bend pipe
  75. Secure 4-tube bundle brake lines onto LH top spacer
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Do not bend pipes
  76. Install 4-tube bundle brake lines onto HCU
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x nuts, 12mm, 16 Nm, Clean lines with brake cleaner before mating as needed
  77. Install fasteners for LH side of shock tower brace
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 15mm, 67 Nm, 1x bolt, 15mm, 62 Nm, Refer to picture proper torque position
  78. Torque fasteners for RH side of shock tower brace
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 15mm, 67 Nm, 1x bolt, 15mm, 62 Nm, Refer to picture proper torque position
  79. Slide the intermediate shaft assembly downward to install it to the steering gear assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Ensure the intermediate shaft is aligned and fully seated,If necessary to align the shaft to steering gear
  80. Install bolt securing the intermediate shaft assembly to the steering gear assembly
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 13mm, 18 Nm
  81. Secure HCU connector harness
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips
  82. Connect HCU connector
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, Seat connection and rotate lever downward, Secure red locking tab
  83. Maneuver front controller into position
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Slide over temp set hook first, then into bottom bracket temp set holes
  84. Secure front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x bolts, 10mm, 10 Nm
  85. Install front controller lower ground strap
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 10 Nm
  86. Install front controller upper ground strap onto body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 10 Nm, Install new bolt
  87. Install harness guide to front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x patch bolts, 8mm, 6 Nm, 1x temp set clip, Install new bolts, Pivot harness guide upwards and back to install temp set clip to front harness, then install bolts
  88. Connect front controller harness connectors
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x connectors, Fully seat connector, then engage locking tabs if equipped
  89. Install front controller protection shield
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 10mm, 8.5 Nm
  90. Connect the supermanifold harness to the front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector
  91. Secure 12V positive cable to front controller
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  92. Install positive terminal cable onto cowl
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x stud, E5, 8 Nm
  93. Secure positive terminal cover
  94. Position the AC compressor and AC compressor bracket assembly into the vehicle for assembly and install the fasteners securing the AC compressor assembly to the strut tower support brace
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bolts, 15mm, 31 Nm, Recommend assistance, Support the AC compressor while installing the fasteners, Carefully install the AC compressor and AC compressor bracket towards the rear of the vehicle, under the strut tower support brace
  95. Install the clip securing the coolant hose to the AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x fir tree clip
  96. Install AC compressor ground strap
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 7 Nm
  97. Install clip securing HV compressor harness to plastic connector housing
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, Take note of original routing
  98. Secure HV harness connector onto AC compressor
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x locking connector, Secure connector and engage black locking tab, Verify fully seated
  99. Install fastener securing AC compressor HV harness bracket to AC compressor
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 13mm, 9 Nm
  100. Secure AC compressor logic connector
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x locking connector, secure connection and engage red locking tab
  101. Install clip securing AC compressor logic connector to HV harness
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x fir tree clip
  102. Install clips securing PT supply hose to AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips
  103. Remove protective fender cover over fan shroud and support
  104. Remove the oil drain container from underneath vehicle
  105. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  106. Secure RDU HV harness onto HV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins
  107. Remove HV insulating gloves
  108. Install the mid aero shield panel. See Verkleidung – Windabweiser – Mitte (Ausbauen und Ersetzen).
  109. Lower vehicle for access to underhood area
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  110. Position LV battery into vehicle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Lower vertically LV battery into the vehicle
  111. Install fasteners securing LV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x bolts, 8mm, 6 Nm Early production vehicle may have 3x bolts, M6, 10mm, 10 Nm
  112. Install negative terminal cable onto body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bolt, 10mm, 10 Nm
  113. Install clip securing negative terminal cable to AC compressor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip
  114. Connect first responder loop and LV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
  115. Fill brake bleeder reservoir to full level
  116. Clean area around brake fluid reservoir and remove brake reservoir cap
  117. Top off brake fluid reservoir
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Top off brake fluid as needed
  118. Install pressure bleeder adapter onto reservoir
  119. Set brake bleed reservoir pressure to 30 psi
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Connect power supply to bleeder and turn on the power, Set pressure to 30 psi, Attach brake bleed reservoir to brake bleed adapter
  120. Connect to vehicle using Toolbox 3.0
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle. https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)
  121. Select Actions/Autodiag and search for "bleed"
  122. Remove bleeding valve covers and install the fluid catching bottle to LH front brake caliper outer bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x covers
  123. Open LH front brake caliper outer bleeding valve then click the play button next to PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDSearch for routine in ToolboxFL and RR brake bleed procedureChassis / Brakes - Brake Bleed FL-RRChassis / Brakes - Brake Bleed FL-RR and select Run to start the ESP, then close the bleeding valve once the pump stop running, then repeat the process for inner bleeding valve, and then lastly repeat the process for outer bleeding valve again
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  124. Repeat the above step till clear fluid and no air bubbles come out of the LH front brake caliper bleeding valve
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  125. Remove the fluid catching bottle, Torque LH front brake caliper bleeding valves then install covers
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  126. Remove bleeding valve covers and install the fluid catching bottle to RH front brake caliper outer bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x covers
  127. Open RH front brake caliper outer bleeding valve then Click the play button next to PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDSearch for routine in ToolboxFR and RL brake bleed procedureChassis / Brakes - Brake Bleed FR-RLChassis / Brakes - Brake Bleed FR-RL and select Run to start the ESP, then close the bleeding valve once the pump stop running, then repeat the process for inner bleeding valve, and then lastly repeat the process for outer bleeding valve again
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  128. Repeat the above step till clear fluid and no air bubbles come out of the RH front brake caliper bleeding valves
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  129. Remove the fluid catching bottle, Torque RH front brake caliper bleeding valves and install covers
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  130. Remove bleeding valve cover and install the fluid catching bottle to RH rear brake caliper bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x cover
  131. Open RH rear brake caliper bleeding valve then Click the play button next to PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDSearch for routine in ToolboxFL and RR brake bleed procedureChassis / Brakes - Brake Bleed FL-RRChassis / Brakes - Brake Bleed FL-RR and select Run to start the ESP, then close the bleeding valve once the pump stop running
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  132. Repeat the above step till clear fluid and no air bubbles come out of the RH rear brake caliper bleeding valve
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  133. Remove the fluid catching bottle, Torque RH rear brake caliper bleeding valve and install cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  134. Remove bleeding valve cover and install the fluid catching bottle to LH rear brake caliper bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x cover
  135. Open LH rear brake caliper bleeding valve then Click the play button next to PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDSearch for routine in ToolboxFR and RL brake bleed procedureChassis / Brakes - Brake Bleed FR-RLChassis / Brakes - Brake Bleed FR-RL and select Run to start the ESP, then close the bleeding valve once the pump stop running
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  136. Repeat the above step untill clear fluid and no air bubbles come out of the LH rear brake caliper bleeding valve
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  137. Remove the fluid catching bottle, Torque LH rear brake caliper bleeding valve and install cover
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  138. Power off brake bleed reservoir and detach brake bleed reservoir from brake bleed adapter
  139. Remove pressure bleeder adapter from reservoir
  140. Check fluid level
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Top off if necessary
  141. Install brake reservoir cap
  142. Pump the brake pedal a few times to ensure the brake pedal feels normal
  143. Mit Toolbox 3.
    1. Wählen Sie die Registerkarte Actions, und suchen Sie nach „Steifigkeit“.
    2. Wählen Sie die ODIN-Routine TEST_BRAKE_X_STIFFNESS-TEST-SERVICESearch for routine in ToolboxIBST Stiffness Test - Service - BURNISHED/UNBURNISHEDChassis / Brakes - Brake Stiffness Test, und klicken Sie dann auf den Link der Routine.
    3. Wenn die Bremsbeläge oder Bremsscheiben ersetzt wurden, wählen Sie UNBURNISHED unter „Action_Type“. Wählen Sie in allen anderen Fällen BURNISHED.
    4. Klicken Sie auf RUN, und lassen Sie die Routine durchlaufen.
      Informational PurposesAn informational icon, calling your attention
      Anmerkung
      Treten Sie während des Tests nicht auf das Bremspedal.
  144. Remove ethernet cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
  145. Raise vehicle partially and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  146. Install the LH and RH front wheel arch liners. See Radhausverkleidung – Vorne – LH (Strukturpack) (Ausbauen und Ersetzen).
  147. Install all 4 wheels. See Radbaugruppe (Aus- und Einbauen).
  148. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  149. Install clipping points securing compressor HV harness to front of vehicle body
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x clips, Return to original routing, Verify fully secured
  150. Install RH front wheel liner to HV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, 1x bolt, 10mm, 5 Nm
  151. Install LH front wheel liner to HV battery
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x clip, 1x bolt, 10mm, 5 Nm
  152. Apply Loctite 222 onto front aero shield bolts and install fasteners securing front aero shield to vehicle
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    12x bolts, 10mm, 6 Nm, 2x nuts, 15mm, 6 Nm, 2x clips, 2x hooks
  153. Lower vehicle until tires are touching the ground
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  154. Torque all four wheels
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    5x nuts (each wheel), 21mm, 175 Nm
  155. Install all four wheel caps
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x cap, Align valve stem with wheel cap cavity
  156. Install the HEPA duct. See Kanal – HEPA (Ausbauen und Ersetzen)
  157. Install the HEPA filter. See Baugruppe – Filter – HEPA (Ausbauen und Ersetzen).
  158. Install the underhood storage unit. See Frontstauraum (Ausbauen und Ersetzen).
  159. Install the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
  160. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Lower rack arms fully and remove from under vehicle
  161. Raise the LH front window and close the LH front door
  162. Perform test drive
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Per current FRT (00040100) 0.3 hrs, If alignment was adjusted verify tracking, If DAS components were adjusted verify operation, If brakes were serviced perform burnishing