01/11/2023 11:29:29

Steuergerät – Ladeanschluss (7-Sitzer) (Ausbauen und Ersetzen)

Korrekturcode 44015032 0.36 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warnung
Bei diesem Verfahren handelt es sich um einen ENTWURF, der jedoch bereits validiert wurde. Warn- und Sicherheitshinweise sind möglicherweise nicht vorhanden. Befolgen Sie die Sicherheitshinweise, und gehen Sie beim Arbeiten an oder in der Nähe von Hochspannungssystemen und -bauteilen äußerst vorsichtig vor. Übermitteln Sie Verbesserungsvorschläge und Feedback an ServiceDevelopment@teslamotors.com.
  1. Place vehicle in service mode through UI
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Select vehicle's badge icon in Controls > Software for four seconds and then type "service" into dialog boxAnd then touch "ok"At last Select ‘X’ at top left of window to close once complete
  2. Open the LH front door.
  3. Lower all four windows
  4. Move LH front seat forward
  5. Open LH rear door
  6. Tilt 7s 2nd row 60 seat forward
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Hold 2nd row 60 seat LH shoulder switch, Slide seat all the way forward and tit up
  7. Partially remove LH rear door seal
  8. Remove LH 7s lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips
  9. Open liftgate
  10. Release 3rd row LH seat backrest
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Front switch at LH trunk trim panel
  11. Release 3rd row RH seat backrest
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Rear switch at LH trunk trim panel
  12. Remove rear load floor
  13. Remove trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips
  14. Remove 7s LH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips
  15. Remove LH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x connectors, 1x push clip, 8x clips, 7x tabs, guide front clip stanchions around LH C-pillar, trim part may slightly differ, by vehicle build location
  16. Release top edge of LH 7s trunk side trim and disconnect 12V outlet and trunk switch connectors
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    6x clips, 2x connectors
  17. Release remaining clips and remove LH 7s trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar, Pull the top of the trunk side trim all the way down flat so it clears the edge of the folded down LH 3rd row seatback and pull straight out
  18. Disconnector ECU connectors.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    3x connectors
  19. Remove Charge Port ECU
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x 10mm bolt, slide the Charge Port ECU to the front of the vehicle.
  20. Install Charge Port ECU
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x 10mm bolt, 3x connectors, slide the Charge Port ECU to the rear of the vehicle
  21. Re-install software via UI
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Via Controls > Service Mode > Software Reinstall
  22. Select "REQUEST" to initiate software installation
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Vehicle will send a request to Tesla server for the re-installation of the current firmware, Read instructions on the UI then select request if you meet the criteria, Vehicles with software version before 2022.20.7 will require internet connectivity to request the software job from the server
  23. Position LH 7s trunk side trim and install lower clips
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x push clips, 5x clips, Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly, Guide front clip stanchions around LH C-pillar
  24. Connect 12V outlet and trunk switch connectors then install top edge of LH 7s trunk side trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    6x clips, 2x connectors
  25. Install LH trunk pocket bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    1x push clip, 5x alignment tabs
  26. Install 7s LH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    2x clips
  27. Install trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    4x clips, Seat seal around edge of trim
  28. Install rear load floor
  29. Raise 3rd row RH seat backrest to its original position
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Manually raise backrest up to its original position until it locks into place
  30. Raise 3rd row LH seat backrest to its original position
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Manually raise backrest up to its original position until it locks into place
  31. Close liftgate
  32. Install LH 7s lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips
  33. Reseat LH rear door seal
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Seat pillar and sill trim tabs underneath seal
  34. Position 7s 2nd row 60 seat back to its original position
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Tilt 2nd row 60 seat down, Press LH shoulder switch and slide back into original position
  35. Close LH rear door
  36. Move LH front seat to original position
  37. Verify operation of charging system
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Use customer's charging equipment if available, Ensure all charging adapters are present
  38. Raise all four windows
  39. Close the LH front door.