20/12/2022 14:36:24

Bremsleitungen – Hauptzylinder zum ABS (ohne Strukturpack) (RHD) (Ausbauen und Ersetzen)

Korrekturcode 33034202 2.04 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden.HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. Für Rückmeldungen zu den FRT-Werten senden Sie bitte eine E-Mail an LaborTimeFeedback@tesla.com. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen.

Ausbauen

  1. Open the RH front door and lower the RH front window.
  2. Remove the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
  3. Remove the underhood storage unit. See Frontstauraum (Ausbauen und Ersetzen).
  4. Disconnect 12V power. See 12-V-/Niederspannungsversorgung (Trennen und Verbinden).
  5. Remove the 12V battery. See 12-V-/LV-Batterie (Ausbauen und Ersetzen).
  6. Remove the fresh air intake duct. See Kanal – HEPA (Ausbauen und Ersetzen).
  7. Remove the front aero shield. See Verkleidung – Windabweiser – Vorne (Nicht Strukturpack) (Ausbauen und Ersetzen).
  8. Remove the fir tree clips (x4) that attach the coolant hoses to the AC compressor bracket.
  9. Remove the retaining clips (x2) that attach the AC compressor HV harness to the shock tower brace.
  10. Remove the LH and RH bolts that attach the shock tower brace to the body.
    55 Nm (40.6 lbs-ft)
    55 Nm (40.6 lbs-ft)
  11. Remove the LH and RH outer bolts that attach the shock tower brace to the body.
    62 Nm (45.7 lbs-ft)
  12. Disconnect the HVIL connector.
  13. Remove the bolts (x2) that attach the AC compressor bracket to the shock tower brace.
    31 Nm (22.9 lbs-ft)
  14. Carefully remove the AC compressor and AC compressor bracket towards the front of the vehicle, under the shock tower brace.
  15. Disconnect the electrical connector from the ABS unit.
  16. Position the oil drain under the ABS unit.
  17. Loosen the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  18. Loosen the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  19. Place an absorbent material beneath the brake booster and reservoir area.
  20. Using a brake fluid syringe, remove the brake fluid from the reservoir.
  21. Loosen the nut that attaches the secondary brake line to the master cylinder, and then remove the secondary brake line.
    16 Nm (11.8 lbs-ft)
  22. Loosen the nut that attaches the primary brake line to the master cylinder, and then remove the primary brake line.
    16 Nm (11.8 lbs-ft)
  23. Release the primary and secondary brake lines from the brake line bundle clip.
  24. Remove the bolts (x2) that attach the ABS unit to the frame rail.
    10 Nm (7.4 lbs-ft)
  25. Move the ABS unit and bracket towards the 12V battery area to make sure there is space to remove the brake lines.
  26. Remove the brake lines from the bundle clips (x2) under the ABS unit.
  27. Remove and discard the bolts (x2) that attach the harness guide to the front controller, and then release the harness guide.
    6 Nm (4.4 lbs-ft)
  28. Remove brake line bundle clips (x3).
  29. Route the master cylinder brake lines towards the right controller, and then remove the master cylinder brake line bundle from the vehicle.

Montieren

  1. Route the master cylinder brake lines from the controller towards the ABS unit, and then put the brake lines into position.
  2. Install the brake line bundle clips (x3).
  3. Mount the brake lines to the bundle clips (x2)under the ABS unit.
  4. Fasten the bolts (x2) that attach the harness guide to the front controller.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Replace the patchbolts.
    6 Nm (4.4 lbs-ft)
  5. Mount the primary and secondary brake lines to the brake line bundle clip.
  6. Fasten the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  7. Fasten the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  8. Clean the ABS unit surface of residual brake fluid.
  9. Put the ABS unit and bracket into position.
  10. Remove the oil drain container from underneath vehicle
  11. Install the bolts (x2) that attach the ABS unit to the frame rail.
    10 Nm (7.4 lbs-ft)
  12. Install the secondary brake line to the master cylinder, and then fasten the nut that attaches the secondary brake line.
    16 Nm (11.8 lbs-ft)
  13. Install the primary brake line to the master cylinder, and then fasten the nut that attaches the primary brake line.
    16 Nm (11.8 lbs-ft)
  14. Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
  15. Carefully position the AC compressor and AC compressor bracket into the vehicle.
  16. Fasten the bolts (x2) that attach the AC compressor bracket to the shock tower brace.
    31 Nm (22.9 lbs-ft)
  17. Install the fir tree clips (x4) that attach the coolant hoses to the AC compressor bracket.
  18. Install the LH and RH bolts that attach the shock tower brace to the body.
    55 Nm (40.6 lbs-ft)
    55 Nm (40.6 lbs-ft)
  19. Install the LH and RH outer bolts that attach the shock tower brace to the body.
    62 Nm (45.7 lbs-ft)
  20. Install the retaining clips (x2) that attach the AC compressor HV harness to the shock tower brace.
  21. Connect the HVIL connector
  22. Install the 12V battery. See 12-V-/LV-Batterie (Ausbauen und Ersetzen).
  23. Reconnect 12V power. See 12-V-/Niederspannungsversorgung (Trennen und Verbinden).
  24. Install the fresh air intake duct. See Kanal – HEPA (Ausbauen und Ersetzen).
  25. Install the underhood storage unit. See Frontstauraum (Ausbauen und Ersetzen).
  26. Bleed the brakes. See Bremsflüssigkeit entlüften/spülen
  27. Install the front aero shield. See Verkleidung – Windabweiser – Vorne (Nicht Strukturpack) (Ausbauen und Ersetzen).
  28. Install the rear underhood apron. See Unterhaubenschürze – Hinten (Ausbauen und Ersetzen).
  29. Perform a test drive.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Per current FRT (00040100) 0.3 hrs, If alignment was adjusted verify tracking, If DAS components were adjusted verify operation, If brakes were serviced perform burnishing