2026-03-30

Rear Fascia Assembly (Model Y Standard) (Remove and Install)

Code de correction 10011400501 0.48 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
  • 2026-03-16: Released new procedure.

Retirer

  1. Open the LH rear door.
  2. Lower the LH rear window.
  3. Remove the LH rear fender garnish from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x tabs, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
  4. Remove the screw that secure the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, 8mm, 2 Nm
  5. Remove the LH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  6. Remove the bolt that secures the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 3.5 Nm
  7. Open the RH rear door.
  8. Lower the RH rear window.
  9. Remove the RH rear fender garnish from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x tabs Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
  10. Remove the screw securing the RH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, 8mm, 2 Nm
  11. Remove the RH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  12. Remove the bolt that secures the RH corner of the rear fascia to the body,
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 3.5 Nm
  13. Remove the rear fascia diffuser front bolts (x2)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10mm, 5 Nm
  14. Release the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers
  15. Release the rear fascia assembly from the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Disengage locking tab, Recommend assistance, Place rear fascia on padded surface to avoid damage

Installer

  1. Secure the rear fascia assembly onto the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Engage locking tab, Recommend assistance
  2. Secure the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers, Apply Loctite 222 onto bolts
  3. Install the rear fascia diffuser front bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts
  4. Install the bolt that secures the RH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 3.5 Nm
  5. Install the RH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  6. Install the screw that secures the RH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, 10mm, 2 Nm
  7. Install the RH rear fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x tabs, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  8. Raise the RH rear window.
  9. Close the RH rear door.
  10. Install the bolt that secures the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 3.5 Nm
  11. Install the LH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  12. Install the screw that secures the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, 8mm, 2 Nm
  13. Install the LH rear fender garnish to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x tabs, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  14. Return the 2nd row 60 seatback to vertical position.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via trunk seat switch, Remove seatback protection if necessary
  15. Close the liftgate.
  16. Raise the LH rear window.
  17. Close the LH rear door.