2026-07-31

Coax Cable - Side Repeater - Front - LH and RH (Overlay) (Remove and Replace)

Code de correction 17403032 2.88 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Avertissement

Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.

2026-07-09: Released new procedure.

Overlay

Raise and support vehicle

Remarque
Ensure vehicle is not charging
Open LH front door
Lower LH front window
Open RH front door
Lower RH front window
Move RH front seat backward
Remove the wiper module. See Wiper Module (LHD) (Remove and Replace).
Remove fresh air intake assembly

Remarque
2x studs, Lift cowl as needed
Remove RH front wheel center cap

Remarque
1x cap, Pull the inner side of the adjacent 2 claws on the wheel center cap by hands
Loosen RH front wheel nuts

Remarque
5x nuts, 21mm, 175 Nm
Remove LH front wheel center cap

Remarque
1x cap, Pull the inner side of the adjacent 2 claws on the wheel center cap by hands
Loosen LH front wheel nuts

Remarque
5x nuts, 21mm, 175 Nm
Raise vehicle partially and lower lift onto locks

Remarque
Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side
Remove RH front wheel

Remarque
5x nuts, 21mm, 175 Nm
Partially remove RH front wheel liner

Remarque
8x clips, 1x bolt, 10mm, 5 Nm
Disconnect the front harness connectors for the RH side repeater and camera

Remarque
2x connectors, Release locking tabs
Remove LH front wheel

Remarque
5x nuts, 21mm, 175 Nm
Partially remove LH front wheel liner

Remarque
8x clips, 1x bolt, 10mm, 5 Nm
Disconnect the front harness connectors for the LH side repeater and camera

Remarque
2x connectors, Release locking tabs
Lower vehicle partially and set lift onto locks

Remarque
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
Power off vehicle from center display

Remarque
Via Controls > Safety > Power Off, Select Power Off button at warning dialog box
Disconnect LV battery and first responder loop

Remarque
2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
Disconnect thermal sub-harness from front controller

Remarque
1x connector, Depress locking tab and rotate to release
Remove bolts securing front controller shield assembly and remove from vehicle

Remarque
2x bolts, 10mm, 8.5 Nm
Disconnect front controller harness connectors

Remarque
5x connectors, 1x harness guide, Release locking tab if equipped
Remove bolt securing ground cable to front controller

Remarque
1x bolt, 10mm, 8.5 Nm,
Remove bolts securing front controller

Remarque
3x bolts, 10mm, 10 Nm
Tilt front controller forward for access

Remarque
Lift cowl screen up appropriately
Release LV negative harness clip from front controller

Remarque
1x clip
Remove front controller from vehicle

Remarque
1x tab
Release RH footwell cover

Remarque
2x magnets, 1x guide tab, 1x connector
Partially release RH front primary door seal

Remarque
Release lower section of RH front primary door seal
Remove RH IP end cap

Remarque
5x clips, 2x guide tabs
Remove RH lower A-pillar trim

Remarque
4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
Remove RH knee airbag bolt covers

Remarque
2x covers
Remove RH knee airbag bolts

Remarque
4x bolts, EP10, 8.5 Nm, Discard bolts after removal, brake loose e10 by hand then use e-ratchet to back off hardware
Remove RH knee air bag assembly

Remarque
1x air bag connector, 1x connector, Peel back plastic film, Release by pulling back both white tabs simutaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side
Remove clips securing passenger footwell duct

Remarque
2x clips
Disconnect glove box USB cable connector from car computer

Remarque
1x connector, Release locking tab then release connector
Remove screws securing glove box to IP

Remarque
4x screws, T20, 2.3 Nm
Release glove box from IP assembly

Remarque
10x clips, 3x locator pins, 1x datum, Avoid damage to electromagnetic switch
Remove glove box

Remarque
2x connectors
Remove RH passenger footwell duct from HVAC module
Disconnect RH IP air wave duct thermistor connector

Remarque
1x connector
Remove RH IP air wave duct from HVAC module
Unfold RH front main cabin carpet back to original position

Remarque
1x locator clip
Release windshield heater connecter

Remarque
1x connector
Release RH grommet from body
Remove electrical tape securing harness bundle to rubber dust boot

Remarque
Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
Remove locking pin from connector

Remarque
Carefully pry pin out of connector and fully remove locking pin
Remove coax cable needed for the side repeater overlay terminal 2 (LHS)

Remarque
Inspect all components for damage
Remove coax cable needed for the side repeater overlay terminal 1 (RHS)

Remarque
Inspect all components for damage
Apply harness tape onto LH coax overlay cable before installation

Remarque
Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
Apply harness tape onto RH coax overlay cable before installation

Remarque
Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
Release frunk harness cover

Remarque
3x tabs
Position M3 LH coax overlay cable into place, Place through LH wheel liner

Remarque
Pull till you have roughly 12 inches of cable towards the interior of the vehicle
Pull LH coax overlay cable through frunk harness

Remarque
Pull harness towards car computer, Route under brake booster lower connector
Tape coax overlay onto fish nylon tape
Release frunk harness cover

Remarque
3x tabs
Position M3 LH coax overlay cable into place, Place through LH wheel liner

Remarque
Pull till you have roughly 12 inches of cable towards the interior of the vehicle
Pull LH coax overlay cable through frunk harness

Remarque
Pull harness towards car computer, Route under brake booster lower connector
Tape coax overlay onto fish nylon tape
Pull LH coax overlay cable through bulkhead and into interior cabin
Remove nylon fish tape

Remarque
Remove tape the pull nylon fish tape out of vehicle
Pull RH coax overlay cable through RH grommet harness

Remarque
Pull harness toward car computer under RH grommet main harness
Position RH coax overlay cable into place, Place through RH wheel liner

Remarque
Pull till you have roughly 6 inches of cable towards the interior of the vehicle
Tape coax overlay onto fish nylon tape
Pull RH coax overlay cable through bulkhead and into interior cabin
Remove nylon fish tape

Remarque
Remove tape the pull nylon fish tape out of vehicle
Disconnect side repeater cameras connector from car computer

Remarque
1x locking connector
Remove locking pin from side repeater cameras connector

Remarque
Carefully pry pin out of connector and fully remove locking pin
Remove coax terminal 2 (LHS) cable from connector

Remarque
Inspect all components for damage
Remove coax terminal 1 (RHS) cable from connector

Remarque
Inspect all components for damage
Insert new side repeater coax terminal 1 (RHS) cable onto side repeater cameras connector

Remarque
Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm
Insert new side repeater coax terminal 2 (LHS) cable onto side repeater cameras connector

Remarque
Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm
Secure locking pin to connector

Remarque
Align tabs of lock in connector housing, Ensure flush installation of locking pin to connector housing
Connect side repeater cameras connector onto car computer

Remarque
1x locking connector
Position LH coax overlay cable onto frunk main harness, Secure cable onto harness using zip ties

Remarque
7x zip-ties, Trim off excess material after harness has been secured
Cut off the vehicle side repeater coax terminal and tape to vehicle harness

Remarque
Cut the coax connector only
Connect front harness connectors for LH side repeater and camera

Remarque
2x connectors, Secure locking tabs
Position RH coax overlay cable onto frunk main harness grommet, Secure cable onto harness using zip ties

Remarque
3x zip-ties, Trim off excess material after harness has been secured
Cut off the vehicle side repeater coax terminal and tape to vehicle harness

Remarque
Cut the coax connector only
Connect front harness connectors for the RH side repeater and camera

Remarque
2x connectors, Secure locking tabs
Secure RH grommet from body

Remarque
Use electrical tape to wrap the end of the dust boot
Secure frunk harness cover

Remarque
3x tabs
Secure windshield heater connector

Remarque
1x connector
Install LH front wheel liner to vehicle

Remarque
8x clips, 1x bolt, 10mm, 5 Nm
Install LH front wheel

Remarque
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
Install RH front wheel liner to vehicle

Remarque
8x clips, 1x bolt, 10mm, 5 Nm
Install RH front wheel

Remarque
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool, Torque at later step
Lower vehicle until tires are touching ground

Remarque
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Torque LH front wheel

Remarque
5x nuts, 21mm, 175 Nm
Install LH front wheel center cap

Remarque
1x cap, Ensure that the cap is installed in place
Torque RH front wheel

Remarque
5x nuts, 21mm, 175 Nm
Install RH front wheel center cap

Remarque
1x cap, Ensure that the cap is installed in place
Place front controller into vehicle for installation

Remarque
1x tab
Secure LV negative harness clip from front controller

Remarque
1x clip
Tilt front controller backward for installation

Remarque
Lift cowl screen up appropriately
Install bolts securing front controller

Remarque
3x bolts, 10mm, 10 Nm
Install bolt securing ground cable to front controller

Remarque
1x bolt, 10mm, 8.5 Nm,
Connect front controller harness connectors

Remarque
5x connectors, 1x harness guide, Secure locking tab, if equipped
Install front controller shield to front controller

Remarque
2x bolts, 10mm, 8.5 Nm
Connect thermal sub-harness to front controller

Remarque
1x connector, Rotate fully to secure locking tab
Install the wiper module. See Wiper Module (LHD) (Remove and Replace).
Install fresh air intake assembly

Remarque
2x studs, Lift cowl as needed
Position frunk assembly to vehicle

Remarque
8x clips, 3x locator pins, Ensure clips are aligned at thermal beam, Replace any clips if broken or missing
Install bolts securing frunk assembly

Remarque
4x bolts, 10mm, 5 Nm, Number of bolts may vary depending on build date
Install access panel to frunk assembly

Remarque
3x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push forward to secure clips
Install fresh air gutter assembly

Remarque
3x clips
Install RH IP air wave duct to HVAC module
Install clips securing RH IP air wave duct

Remarque
2x push clips
Connect thermistor connector RH IP air wave duct

Remarque
1x connector
Install RH passenger footwell duct to HVAC module
Position glove box assembly

Remarque
2x connectors
Install glove box into IP assembly

Remarque
10x clips, 3x locator pin, 1x datum, If necessary, Replace any clips that are broken
Install screws securing glove box assembly to IP assembly

Remarque
4x screws, T20, 2.3 Nm
Connect glove box USB cable to car computer

Remarque
1x connector, Engage locking tab
Install clips securing passenger footwell duct

Remarque
2x push clips, Ensure that the footwell duct is installed in place
Install RH IP end cap

Remarque
5x clips, 2x guide tabs
lnstall seat lower section of RH front primary seal

Remarque
Verify seal is seated properly on all trim panels
Install RH knee air bag assembly

Remarque
1x air bag connector, 1x connector, Ensure airbag connector is fully engaged, Place plastic film back over squib assembly
Install RH knee airbag bolts

Remarque
4x bolts, EP10, 8.5 Nm, use socket wrench to start hardware by hand to avoid cross threading. Avoid Over tightening Hardware during installation avoid using power tools
Install RH knee air bag bolt covers

Remarque
2x covers
Install RH footwell cover

Remarque
2x magnets, 1x guide tab, 1x connector
Connect first responder loop and LV battery

Remarque
2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
Install rear apron

Remarque
14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
Close hood
Move RH front seat to original position
Raise RH front window
Close RH front door
Verify operation of windshield washers and wipers
Clear DAS Calibration through UI

Remarque
Controls > Service > Camera Calibration, Select Clear Calibration, Verify calibration was cleared successfully, Wait for prompt to disappear automatically before continuing, Calibration in Progress message and progress icon will appear during the next drive cycle
Raise LH front window
Close LH front door
Remove lift arms from below vehicle

Remarque
Lower rack arms fully and remove them from under vehicle
Vehicle will need to be driven by customer to complete calibration procedure. During this time DAS functions will be completely unavailable