07/11/2023 16:08:23

Hose - Powertrain Supply (Remove and Replace)

Code de correction 1830020112 FRT 0.72 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 1080568-00-A Fluid Catcher
  • 1135762-00-A Trousse, prise Svc, flexible liquide refroidissement, Model 3
  • 1065131-00-A Kit, Battery Coolant Drain
Tableau 1. Caractéristiques techniques de couple : Hose - Powertrain Supply (Remove and Replace)
Description Valeur de couple Outils recommandés Réutiliser/remplacer Remarques
Boulon qui fixe la doublure de passage de roue avant droite à la plaque de protection
5 Nm (3.7 lbs-ft)
  • Clé à rochet 1/4 po sans fil
  • Pose-écrou 1/4 po, 6 po Mèche longue magnétique X 10 mm
  • Douille longue de 10 mm
  • Clé à cliquet/Clé dynamométrique
 Réutiliser

Retirer

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Disconnect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  3. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  4. Raise the vehicle fully and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  5. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Remove the bolt that secures the RH front wheel liner to the skid plate.
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Clé à rochet 1/4 po sans fil
    • Pose-écrou 1/4 po, 6 po Mèche longue magnétique X 10 mm
    • Douille longue de 10 mm
    • Clé à cliquet/Clé dynamométrique
  7. Remove the push clips (x3) that secure the lower rear edge of the RH front wheel liner to the vehicle for access to the coolant hose.
  8. Use a bungee strap to pull back the RH front wheel liner and secure it to the subframe.
  9. Position the coolant drain container underneath the RH front of the HV battery.
  10. Release the spring clip and the plugs (x2) to disconnect the powertrain supply hose from the powertrain supply tube, and then plug the ends of both fittings as soon as possible to avoid coolant loss.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Coolant loss greater than 1L requires vacuum fill.
  11. Release the powertrain supply hose clips (x2) from the vehicle.
  12. Remove the coolant drain container from underneath the vehicle.
  13. Lower the vehicle to a comfortable working height and set the lift onto locks.
  14. Position the fluid catcher underneath the front of the vehicle.
  15. Remove the fresh intake duct. See Fresh Air Intake - HVAC (Remove and Replace).
  16. Pull the red locking tab to disengage the lock, and then hold and pull it again to release the electrical connector, so that the powertrain supply hose sensor is disconnected.
  17. Release the spring clip and the plugs (x2) to disconnect the powertrain supply hose from the supermanifold, and then plug the ends of both fittings as soon as possible to avoid coolant loss.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Coolant loss greater than 1L requires vacuum fill.
  18. Remove the powertrain supply hose from the vehicle.

Installer

  1. Install the powertrain supply hose to the vehicle and place a coolant plug on the lower end of the hose to avoid coolant loss.
  2. Remove the plugs on the ends of fittings as quickly as possible to avoid coolant loss, and then secure the spring clip and the plug to connect the powertrain supply hose to the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Perform a push-pull-push test to make sure that the hose is fully secured.
  3. Engage the locking tab to connect the powertrain supply hose sensor.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The harness and the coolant hose are color coded. Match the color of the harness to the color of the coolant hose.
  4. Install the fresh intake duct. See Fresh Air Intake - HVAC (Remove and Replace).
  5. Remove the fluid catcher from underneath the vehicle.
  6. Raise the vehicle fully and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  7. Position the coolant drain container underneath the RH front of the HV battery.
  8. Remove the plugs on the ends of fittings as quickly as possible to avoid coolant loss, and then secure the spring clip and the plugs (x2) to connect the powertrain supply hose to the powertrain supply tube.
    Informational PurposesAn informational icon, calling your attention
    Remarque

    Perform a push-pull-push test to make sure that the hose is fully secured.

    Coolant loss greater than 1L requires vacuum fill.

  9. Secure the powertrain supply hose clips (x2) to the vehicle.
  10. Remove the coolant drain container from underneath the vehicle.
  11. Release the RH front wheel liner from the bungee strap, and remove the strap from the vehicle.
  12. Install the push clips (x3) that secure the lower rear edge of the RH front wheel liner to the vehicle.
  13. Install the bolt that secures the RH front wheel liner to the skid plate.
    5 Nm (3.7 lbs-ft)
    Conseil : Nous recommandons l’utilisation des outils suivants :
    • Clé à rochet 1/4 po sans fil
    • Pose-écrou 1/4 po, 6 po Mèche longue magnétique X 10 mm
    • Douille longue de 10 mm
    • Clé à cliquet/Clé dynamométrique
  14. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  15. Lower the vehicle fully.
  16. Connect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  17. Remove the coolant bottle cap and fill the coolant to the "MAX" line.
  18. Unlock the vehicle gateway. See Déverrouillage de passerelle.
  19. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Coolant System > Coolant Purge > Run to start the coolant air purge.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    • The routine will last for a while after the stop message displays. The coolant pumps are audible.
    • The test lasts for approximately 10 mins. Do not start another routine during this time.
    • Make sure that the vehicle is not in Drive. Putting the vehicle into Drive will stop this routine.
    • The speed in the test varies from 3500-6500 RPM (idle speed = ~1500 RPM) and the actuated valve varies between SERIES and PARALLEL.
    • Si la vitesse oscille à 7 000 tr/min, cela signifie que les pompes sont bloquées par l’air. Recommencez le remplissage sous vide. Continuez à ajouter du liquide de refroidissement et à purger jusqu’à ce que le niveau de liquide de refroidissement se trouve entre les lignes NOM et MAX de la bouteille.
  20. Inspect the coolant level, top off as necessary, and then install the coolant bottle cap.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure that the coolant level is at the "Max" line.
  21. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  22. Raise the LH front window and close the LH front door.
  23. Remove the lift arms from below the vehicle.