Code de correction 00030410 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiquespour consulter les pratiques de travail sécuritaires et saines.

1. Inspect front external lights
   Remarque

   Look for cosmetic damages and humidity ingress

   

2. Inspect rear external lights
   Remarque

   Look for cosmetic damages and humidity ingress, it is acceptable for taillights to have some condensation

   

3. Link to procedure: 686540f6e03b756b141c53ec
4. Inspect windshield for rock chips and cracks
   Remarque

   No damage in the driver’s viewing area, airbag impact area, forward camera viewing area, or within 50 mm of the edge allowed, No more than 3 cracks or chips to the glass allowed

   

5. Check all emergency release cables and switches
   Remarque

   Front door releases, Trunk release, Use caution with front door releases as door glass will not drop and could damage seals or bright molding

   

   

6. Function check chargeport door (5 cycles)
   Remarque

   5x cycles, Inspect and note functionality full range of motion, touch to open, and indicator light. Look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

   

7. Open liftgate
   Remarque

   Observe for proper latch operation

   

8. Close trunk

   

   

9. Function check LH front door (exterior)
   Remarque

   Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

   

10. Function check LH front door (interior)
    Remarque

    Inspect and note functionality for the interior door release, puddle lamps, and manual release cable, From inside look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

    

11. Function check all windows from the master switch
    Remarque

    Document any abnormal operation/noises

    

12. Function check LH rear door (exterior)
    Remarque

    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

    

13. Function check LH rear door (interior)
    Remarque

    Inspect and note functionality for the interior door release, and puddle lamps, From inside look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

    

14. Function check LH rear window
    Remarque

    Inspect and note functionality for the window switch, and full range of motion of the window with door closed

    

15. Function check RH rear door (exterior)
    Remarque

    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

    

16. Function check RH rear door (interior)
    Remarque

    Inspect and note functionality for the interior door release and puddle lamps, From inside look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

    

17. Function check RH rear window
    Remarque

    Inspect and note functionality for the window switch, and full range of motion of the window with door closed

    

18. Function check RH front door (exterior)
    Remarque

    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

    

19. Function check RH front door (interior)
    Remarque

    Inspect and note functionality for the interior door release, puddle lamps, and manual release cable, From inside look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

    

20. Function check RH front window
    Remarque

    Inspect and note functionality for the window switch, and full range of motion of the window with door closed

    

21. Function check all driver controls
    Remarque

    Shift stalk, turn signals, steering wheel scroll wheels, horns

    

22. Open glove box through UI
    Remarque

    via Controls > Glovebox

    

23. Close glove box

    

24. Function check power folding side mirrors
    Remarque

    Fold mirrors in/out, Check adjustment of glass

    

    

25. Function check LH front seat
    Remarque

    Check full range of motion of seat, Test lumbar and seat heat/cooling

    

26. Function check LH front seat belt
    Remarque

    Latch and unlatch buckle, Quickly pull retractor to check locking function

    

27. Fold the 60 seat in down position

    

28. Fold 60 seat into vertical position
    Remarque

    Remove seat protection

    

29. Fold the 40 seat in down position

    

30. Fold the 40 seat into vertical position
31. Function check the rear seat belts
    Remarque

    Latch and unlatch buckles, Quickly pull retractors to check locking function

    

32. Function check the RH front seat belt
    Remarque

    Latch and unlatch buckle, Quickly pull retractor to check locking function

    

33. Function check RH front seat
    Remarque

    Check full range of motion of seat

    

34. Verify operation of windshield wipers and nozzles
    Remarque

    Ensure hood and doors are closed prior to activating wipers, Inspect and note functionality for wipers and wiper jets, Check for full range of motion, speed of motion, interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

    

    

35. Link to procedure: 67b88c8a83ed950e257a16e3
36. Open hood
    Remarque

    Press "Open" button on touchscreen to release latch, Lift lid manually

    

    

37. Fill washer reservoir with fluid

    

38. Remove rear apron
    Remarque

    12x clips, Only store rear apron visible face upwards

    

    

    

    

39. Remove cabin intake upper duct assembly
    Remarque

    3x clips, Some configurations may come with 4x clips

    

    

    

40. Remove closeout panel from frunk assembly
    Remarque

    4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Grab closeout panel from bottom then pull it upward to release clips, Disconnect switch

    

    

41. Remove frunk assembly carpet
    Remarque

    Note: Not all Model 3 vehicles have a frunk carpet installed

    

42. Remove bolts securing frunk assembly
    Remarque

    7x bolts, 10mm, 5 Nm

    

43. Remove frunk assembly from vehicle
    Remarque

    12x clips, Replace any clips if broken or missing, Number of clips may vary on older vehicles

    

    

    

    

44. Perform inspection of under hood area
    Remarque

    Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance

    

45. Visually inspect brake fluid level

    

46. Inspect coolant level and top off as necessary
    Remarque

    Ensure that fluid level is at Max line

    

    

47. Raise and support vehicle

    

    

    

48. Remove LH front wheel center cap
    Remarque

    1x cap

    

49. Remove RH front wheel center cap
    Remarque

    1x cap

    

50. Remove RH rear wheel center cap
    Remarque

    1x cap

    

51. Remove RH rear wheel center cap
    Remarque

    1x cap

    

52. Remove LH rear wheel center cap
    Remarque

    1x cap

    

53. Loosen LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

54. Loosen RH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

55. Loosen RH rear wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

56. Loosen LH rear wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

57. Raise vehicle partially and lower lift onto locks
    Remarque

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side

    

    

58. Inspect radiator inlet in front fascia for debris
    Remarque

    Clear debris if necessary

    

59. Remove LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

60. Remove RH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

61. Remove RH rear wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

62. Remove LH rear wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

63. Install brake rotor run out flex bar onto LH rear knuckle and setup for reading
    Remarque

    Pay attention to the clamp location and the routing of the flex bar, firmly connect the indicator rod to the upper link bolt head, fnsure the indicator rod is properly depressed, allowing travel in both directions without bottoming out and set the measurement to zero

    

    

64. Install brake rotor run out flex bar onto LH rear knuckle and setup for reading
    Remarque

    Pay attention to the clamp location and the routing of the flex bar, firmly connect the indicator rod to the upper link bolt head, fnsure the indicator rod is properly depressed, allowing travel in both directions without bottoming out and set the measurement to zero

    

    

65. Remove brake rotor run out flex bar from LH knuckle assembly

    

66. Install brake rotor run out flex bar onto RH rear knuckle and setup for reading
    Remarque

    Pay attention to the clamp location and the routing of the flex bar, firmly connect the indicator rod to the upper link bolt head, fnsure the indicator rod is properly depressed, allowing travel in both directions without bottoming out and set the measurement to zero

    

    

67. Inspect RH Rear Upper Knuckle Ball Joint play
    Remarque

    Insert medium size prybar between the aft link and the knuckle and push to check, make sure the prybar is pushing the noted area in the middle of the link's side, this will give proper measurement and avoid link rotation. Note the values of the analog indicator, replace RH Rear Upper Knuckle Ball Joint if the play is greater than 1,00mm

    

    

    

68. Remove brake rotor run out flex bar from RH knuckle assembly

    

69. Measure and record LH rear brake pad thickness
    Remarque

    Recommend replacement if 2mm or less, Check both inboard and outboard pads

    

70. Inspect LH rear brake rotor condition
    Remarque

    Check for excessive rust or wear, Minimum spec 26mm

    

71. Measure and record RH rear brake pad thickness
    Remarque

    Recommend replacement if 2 mm or less, Check both inboard and outboard pads

    

72. Inspect RH rear brake rotor condition
    Remarque

    Check for excessive rust or wear, Minimum spec 26mm

    

73. Measure and record RH front brake pad thickness
    Remarque

    Recommend replacement if 2mm or less, Check both inboard and outboard pads

    

74. Inspect RH front brake rotor condition
    Remarque

    Check for excessive rust or wear, Minimum spec 30mm

    

75. Measure and record LH front brake pad thickness
    Remarque

    Recommend replacement if 2mm or less, Check both inboard and outboard pads

    

76. Inspect LH front brake rotor condition
    Remarque

    Check for excessive rust or wear, Minimum spec 30mm

    

77. Perform visual inspection of all brake pipes and hoses
    Remarque

    Pay special attention to brake junction points

    

    

78. Record tread depth for LH front tire
    Remarque

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

79. Record tread depth for RH front tire
    Remarque

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

80. Record tread depth for LH rear tire
    Remarque

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

81. Record tread depth for RH rear tire
    Remarque

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

82. Check all four tire pressures manually
    Remarque

    4x tires, 4x caps, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures

    

83. Raise vehicle fully and lower lift onto locks
    Remarque

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

84. Perform inspection of steering components
    Remarque

    Check steering gear joints and electrical connections, Verify components are not bent or damaged

    

    

    

    

    

85. Perform visual inspection of HV battery enclosure
    Remarque

    Check for any dents, scrapes, or other damage

    

86. Remove outer fasteners securing front aero shield
    Remarque

    9x bolts, 10mm, 5 Nm

    

87. Remove front aero shield
    Remarque

    2x nuts, 15mm, 5 Nm

    

    

88. Remove rear aero shield
    Remarque

    13x bolts, 10mm, 5 Nm

    

89. Perform visual inspection of underside of vehicle for any coolant leaks
    Remarque

    Pay special attention to hose connection points

    

    

90. Perform inspection of vehicle underside components front and rear
    Remarque

    Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance

    

    

91. Perform inspection of suspension components
    Remarque

    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed

    

    

92. Inspect all rear lateral and compliance link's rubber bushing
    Remarque

    Look for cracks on the rubber partcompare the location according to the images and follow the guide: Damage is contained to the green zone: Do not replace the part• Damage is in the yellow zone on one side of the bushing: Do not replace the part• Damage is in the yellow zone on both sides of the bushing: Part needs replacement• Damage is in the red zone: Part needs replacement

    

    

93. Install rear aero shield
    Remarque

    13x bolts, 10mm, 5 Nm, Apply Loctite 222 to bolts before installing

    

    

94. Position front aero shield to vehicle and install nuts
    Remarque

    2x nuts, 15mm, 5 Nm

    

    

95. Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield
    Remarque

    9x bolts, 10mm, 5 Nm

    

    

96. Lower vehicle partially
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

97. Install LH rear wheel
    Remarque

    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

    

98. Install LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

    

99. Install RH rear wheel
    Remarque

    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

    

100. Install RH front wheel
     Remarque

     5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool, Torque at later step

     

101. Lower vehicle until tires are touching ground
     Remarque

     Raise lift off locks, Then hold lock release lever to keep locks free while vehicle is lowered

     

     

     

102. Torque LH front wheel
     Remarque

     5x nuts, 21mm, 175 Nm

     

103. Torque RH front wheel
     Remarque

     5x nuts, 21mm, 175 Nm

     

104. Torque RH rear wheel
     Remarque

     5x nuts, 21mm, 175 Nm

     

105. Torque LH rear wheel
     Remarque

     5x nuts, 21mm, 175 Nm

     

106. Install LH rear wheel center cap
     Remarque

     1x cap, Verify emblem is aligned with valve stem

     

107. Install RH rear wheel center cap
     Remarque

     1x cap, Verify emblem is aligned with valve stem

     

108. Install RH front wheel center cap
     Remarque

     1x cap, Verify emblem is aligned with valve stem

     

109. Install LH front wheel center cap
     Remarque

     1x cap, Verify emblem is aligned with valve stem

     

110. Remove vehicle from lift
     Remarque

     Lower rack arms fully and remove from under vehicle

     

111. Exécutez la routine ODIN PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox: (link)
112. Check for active alerts
     Remarque

     Check alert using UI via service mode > active alerts" to "Check alerts using UI via Service Mode > Service Alerts > Active Alerts

     

     

113. Update vehicle firmware if available
     Remarque

     Select the clock on the center display, or go to the Software tab, then select install now to start firmware update. Select Install Now, Tap count down timer until clock runs down to 0, Check the center display and ensure the firmware package is installing

     

     

     

114. Exécutez la routine ODIN PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox: (link)