2025-06-27

Hose - Inlet - Front Drive Unit Inverter (Remove and Replace)

Code de correction 1830020162 FRT 0.42 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous. Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Retirer

  1. Raise and support the vehicle. See Soulever le véhicule - pont élévateur à 2 poteaux.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect the LV power. See LV Battery - Li-lon (Disconnect and Connect) (Modify).
  4. Remove the cabin intake duct. See Assembly - Fresh Air Gutter - HVAC (Remove and Replace).
  5. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Remove the push clips (x3) and bolt that attaches the RH front wheel arch liner to the skid plate.
  7. Use a bungee strap to pull back the RH front wheel arch liner and secure it to the subframe.
  8. Position a coolant drain container underneath the RH front of the HV battery.
  9. Release the clip, disconnect the powertrain return hose from the front drive unit inverter inlet hose, and then immediately plug both fittings.
  10. Position a coolant drain container underneath the LH rear of the front drive unit.
  11. Release the clip, disconnect the front drive unit inverter inlet hose from the front drive unit, and then immediately plug both fittings.
  12. Use a clip prytool to release the clip that attaches the front drive unit inverter inlet hose to the front subframe.
  13. Use a clip prytool to release the clip that attaches the front drive unit inverter inlet hose to the front drive unit.
  14. Remove the front drive unit inverter inlet hose.

Installer

  1. Install the clip that attaches the front drive unit inverter inlet hose to the front drive unit.
  2. Install the clip that attaches the front drive unit inverter inlet hose to the front subframe.
  3. Remove the plugs from the fittings, immediately connect the front drive unit inverter inlet hose to the front drive unit inverter, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  4. Remove the plugs from the fittings, immediately connect the front drive unit inverter inlet hose to the powertrain return hose, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  5. Remove the coolant drain collector from under the vehicle.
  6. Remove the bungee strap from the RH front wheel arch liner.
  7. Install the push clips (x3) and bolt that attaches the RH front wheel arch liner to the skid plate.
  8. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  9. Connect LV power. See LV Battery - Li-lon (Disconnect and Connect) (Modify).
  10. Perform the cooling system (partial refill and bleed) procedure. See Cooling System (Partial Refill and Bleed) (Modify).
  11. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  12. Remove the vehicle from the 2 post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.