2025-03-10

Buckle - Seatbelt - 2nd Row - RH and Center (Remove and Replace)

Code de correction 2005020042 FRT 0.18 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • Torchless Heat Induction Tool - 2152873-00-A

Caractéristiques techniques de couple

Tableau 1. Caractéristiques techniques de couple: Buckle - Seatbelt - 2nd Row - RH and Center (Remove and Replace)
Description Valeur de couple Outils recommandés Réutiliser/remplacer Remarques
Bolt that attaches the RH and center seat buckles to the seat track
40 Nm (29.5 lbs-ft)
  • Rallonge de 3 po
  • Douille de 15 mm
  • Clé à cliquet/Clé dynamométrique
  • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
  • Torchless Heat Induction Tool - 2152873-00-A (for removal only)
 Remplacer

Retirer

  1. Remove the 2nd row seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).
  2. Disconnect the RH and center seat buckle electrical connector.
  3. Use a clip prytool to release the bracket that attaches the female side of the electrical connector to the body studs.
  4. Remove and discard the bolt, and then remove the RH and center seat buckles together.
    Informational PurposesAn informational icon, calling your attention
    TIp
    If the bolt is hard to remove, use an inductive heating tool to melt the adhesive patch material. Position the inductive heating tool coil around the bolt, and then heat the bolt for 20 seconds. Allow the bolt to cool down for 2 minutes, and then remove and discard the bolt. The inductive heater coil, bolt, and adjacent areas will be extremely hot.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Persons that have a pacemaker or any other kind of electronic or metal surgical implant must stay at least 1 m (3 ft) away from the inductive heater while it is in use.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Remove all metallic items (such as coins, keys, electronics, and tools) from pockets before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Ensure that there is a properly-maintained fire extinguisher in the work area before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use the inductive heater in a well-ventilated area.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Rallonge de 3 po
    • Douille de 15 mm
    • Clé à cliquet/Clé dynamométrique
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
    • Torchless Heat Induction Tool - 2152873-00-A (for removal only)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Installer

  1. Install new bolt that attaches the RH and center seat buckles to the body.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the guide pin is aligned.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Rallonge de 3 po
    • Douille de 15 mm
    • Clé à cliquet/Clé dynamométrique
    • Clé à cliquet à tête flexible/clé dynamométrique à tête flexible
    • Torchless Heat Induction Tool - 2152873-00-A (for removal only)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  2. Install the bracket that attaches the female side of the connector to the body studs.
  3. Connect the RH and center seat buckle electrical connector.
  4. Install the 2nd row seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).