2026-04-08

Fusible - compresseur de climatisation - batterie HT (retirez et remplacez)

Code de correction 16304202 4.74 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour veiller à porter l’ÉPI approprié lorsque vous effectuez la procédureci-dessous.

  • 2026-03-27: Updated procedure using Power Conversion System removal and installation.
  • 2026-01-09: Added sealant part number and bead specification.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
Équipement :
  • 1018331-00-B (ADHESIVE,CURE IN PLACE,SILICONE,CRTRDG)

Retirer

  1. Remove the HV battery and the Power Conversion System. See Système de conversion d’énergie (retirez et remplacez)
  2. Remove the nuts (x2) that attach the A/C compressor fuse to the mounting studs.
  3. Use the fuse puller to remove the electrical harness terminal from the mounting stud and move aside.
  4. Use the HV insulated pick together with the fuse puller to carefully move the A/C compressor fuse out from under the electrical harness wires, and out of the front bay of the HV battery.

Installer

  1. Perform a zero adjust of the Hioki resistance meter in preparation to measure resistances later in this procedure. See .
  2. Use the fuse puller to carefully install the A/C compressor fuse onto the mounting studs.
  3. Use the fuse puller to install the electrical harness terminal onto the mounting stud.
  4. Install the nuts (x2) that attach the A/C compressor fuse to the mounting studs.
    2.5 Nm (1.8 lbs-ft)
  5. Use the Hioki resistance meter to measure the resistance at the HV joint of the A/C compressor fuse and the positive DC busbar.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Do not short the side of the probe tip to the edge of the fuse lug.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The resistance must be less than 0.145 mΩ (145 μΩ). There is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
  6. Use the Hioki resistance meter to measure the resistance at the HV joint of the A/C compressor fuse and the electrical harness terminal.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Do not short the side of the probe tip to the edge of the nut's captive washer.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The resistance must be less than 0.145 mΩ (145 μΩ). There is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
  7. Install the Power Conversion System and the HV battery. See Système de conversion d’énergie (retirez et remplacez)