2023-03-17

Écran tactile (HW4) (retrait et remplacement)

Code de correction 21051402 0.36 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

Retirer

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
  1. Open the RH front door.
  2. Lower the RH front window.
  3. Move the RH front seat rearwards.
  4. Disconnect LV power. See Alimentation 12 BT (déconnecter et connecter).
  5. Remove the instrument panel service panel. See Panneau de service - tableau de bord (retirez et remplacez).
  6. Remove the bolts (x2) that attach the touchscreen to the instrument panel carrier.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Rallonge de 2 po
    • Douille longue de 10 mm
    • Clé à cliquet/Clé dynamométrique
  7. Disconnect the touchscreen motor connectors (x2).
  8. Release the tabs (x3) that attach the touchscreen shroud to the touchscreen, and then remove the shroud from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide the display outwards until the shroud fully clears the instrument panel and support. Release the bottom tabs and pull upwards.
  9. Release the clip that attaches the harness to the touchscreen pivot mechanism arm, and then disconnect the touchscreen coax and power connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Support the touchscreen and slide it rearwards to access the connectors.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Outil de levier avec pince
    • Pic à prise souple, embout à 90 degrés, 6 po
  10. Remove the touchscreen and pivot mechanism from the vehicle.
  11. Place the touchscreen and pivot mechanism on a soft and clean working surface.
  12. Release the tabs (x3) that attach the touchscreen lower shroud cover to the touchscreen, and then remove the cover from the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide the lower shroud cover upwards, and then outwards to remove from the touchscreen.
  13. Remove the bolt that attaches the touchscreen ground strap to the touchscreen, and then remove the strap from the touchscreen.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Failure to re-connect the ground strap will result in display functionality issues.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Inspect the ground strap bolt and replace if damaged.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Mini Ratchet Bit Set
  14. Remove the touchscreen pivot mechanism. See Mécanisme - pivot - écran tactile (retrait et remplacement).

Installer

  1. Install the touchscreen pivot mechanism. See Mécanisme - pivot - écran tactile (retrait et remplacement).
  2. Position the touchscreen ground strap on the touchscreen, and then install the bolt that attaches the strap to the touchscreen.
    4 Nm (2.9 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Failure to re-connect the ground strap will result in display functionality issues.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Inspect the ground strap bolt and replace if damaged.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Mini Ratchet Bit Set
    • Torque Wrench 1/4in Dr Hexagon - 1060071-00-A
  3. Position the touchscreen lower shroud cover on the touchscreen, and then install the tabs (x3) that attach the cover to the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide the lower shroud cover downwards until the tabs fully engage.
  4. Position the touchscreen and pivot mechanism on the instrument panel carrier, and then route the display harness behind the LH side of the touchscreen pivot mechanism.
  5. Connect the touchscreen coax and power connectors (x2), and then install the clip that attaches the harness to the touchscreen pivot mechanism arm.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Replace the clip if it is damaged.
  6. Position the touchscreen shroud behind the touchscreen, and then install the tabs (x3) that attach the shroud to the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide the display downwards until the tabs fully engage.
  7. Install the bolts (x2) that attach the touchscreen to the instrument panel carrier.
    11.5 Nm (8.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Rallonge de 2 po
    • Douille de 10 mm
    • Clé à cliquet/Clé dynamométrique
  8. Connect the touchscreen motor connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide the touchscreen fully into the instrument panel brackets after securing the connectors.
  9. Install the instrument panel service panel. See Panneau de service - tableau de bord (retirez et remplacez).
  10. Connect LV power. See Alimentation 12 BT (déconnecter et connecter).
  11. Move the RH front seat to original position.
  12. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3.0 (connecter et déconnecter).
  13. In Toolbox, click the Actions tab, type "display" into the search field, click Display Actuator Test, click Run, and then allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once calibration is successful. Check mechanism wiring and connections if failed.
  14. Click Display Mechanism Calibration, click Run, and then allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once calibration is successful.
  15. Type "display mech" into the search field, click Display Mech Functional Test, click Run, and then allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select ‘X’ at top right of window to close once calibration is successful.
  16. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3.0 (connecter et déconnecter).
  17. Raise the RH front window.
  18. Close the RH front door.