2024-06-03

Faisceau – dispositif pyrotechnique – batterie HT (retrait et remplacement)

Code de correction 16300062 5.10 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Retirer

  1. Move the vehicle to a 2 post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.
  2. Perform a cooling system thermal fill drain. See Fluide thermique - système de refroidissement (remplissage/vidange).
  3. Remove the LH and RH rocker panel scuff plates. See Plaque d’usure – bas de caisse – gauche (retrait et remplacement).
  4. Remove the LH and RH rocker panel moldings. See Moulure – bas de caisse – gauche (retrait et remplacement).
  5. Position the 2 post lift pads for HV battery removal.
  6. Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
  7. Déconnectez l’alimentation basse tension. Voir Alimentation 12 BT (déconnecter et connecter).
  8. Remove the mid aero shield panel. See Panneau - écran aérodynamique - central (retirez et remplacez).
  9. Effectuez la procédure de désactivation HT du véhicule. Voir Procédure de désactivation HT du véhicule.
  10. Retirez le sectionneur de batterie pyro. Voir Sectionneur de batterie pyrotechnique (retirez et remplacez).
  11. Remove the HV Battery. See Batterie HT (AWD) (retirez et installez).
  12. Perform a power conversion system coolant drain. See Liquide de refroidissement du système de conversion de puissance (vidange).
  13. Remove the HV battery front access cover. See Couvercle - accès avant - batterie HT (retrait et installation).
  14. Remove the power conversion system. See Système de conversion d’énergie (retirez et remplacez).
  15. Remove the bolts (x6) that attach the power conversion system mounting tray to the HV battery, and then remove the tray from the HV battery.
  16. Peel the Kapton tape, and then remove the mica shielding from the busbar and insulator.
  17. Release the HV battery pyrotechnic harness clip and patch anchor from the high voltage controller.
  18. Disconnect the HV battery pyrotechnic harness from the high voltage controller connector.
  19. Disconnect the electrical harness from the high voltage controller connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Disconnecting the electrical harness permits easier removal of the HV battery pyrotechnic harness.
  20. Carefully release the HV battery pyrotechnic harness connector from the front tray housing.
  21. Release the clips (x2) that attach the HV battery pyrotechnic harness to the front tray housing on either side of the busbar.
  22. Remove the HV battery pyrotechnic harness out from under the busbar, and out of the HV battery.

Installer

  1. Install the HV battery pyrotechnic harness in under the busbar.
  2. Fasten the clips (x2) that attach the HV battery pyrotechnic harness to the front tray housing on either side of the busbar.
  3. Carefully fasten the HV battery pyrotechnic harness connector into the front tray housing.
  4. Connect the electrical harness to the high voltage controller connector.
  5. Connect the HV battery pyrotechnic harness to the high voltage controller connector.
  6. Use an alcohol wipe to clean the adhesive patch area on top of the high voltage controller, and allow at least 1 minute to dry.
  7. Fasten the HV battery pyrotechnic harness clip, peel the backing and apply the patch anchor to the high voltage controller.
  8. Install the mica shielding onto the busbar and insulator.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Apply new Kapton tape if necessary.
  9. Install the power conversion system mounting tray into the HV battery, and then install the bolts (x6) that attach the tray to the HV battery.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure that no wires are pinched beneath the tray.
  10. Install the power conversion system. See Système de conversion d’énergie (retirez et remplacez).
  11. Install the HV battery front access cover. See Couvercle - accès avant - batterie HT (retrait et installation).
  12. Mesurez la tension à travers les points de montage de déconnexion de la batterie pyrotechnique puis installez la déconnexion de la batterie pyrotechnique Voir Sectionneur de batterie pyrotechnique (retirez et remplacez).
  13. Perform a power conversion system coolant leak test. See Test de fuite de liquide de refroidissement du système de conversion de puissance (sur la table).
  14. Perform an HV battery air leak test. See Test de fuite d'air de la batterie HT (sur la table).
  15. Install the HV Battery. See Batterie HT (AWD) (retirez et installez).
  16. Install the mid aero shield panel. See Panneau - écran aérodynamique - central (retirez et remplacez).
  17. Branchez l'alimentation BT. Voir Alimentation 12 BT (déconnecter et connecter).
  18. Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
  19. Install the LH and RH rocker panel moldings. See Moulure – bas de caisse – gauche (retrait et remplacement).
  20. Install the LH and RH rocker panel scuff plates. See Plaque d’usure – bas de caisse – gauche (retrait et remplacement).
  21. Remove the vehicle from the 2 post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.