2023-02-07

Ensemble de la console centrale (retrait et installation)

Code de correction 15192401 0.36 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Retirer

  1. Ouvrez toutes les portes et abaissez toutes les vitres.
  2. Move the driver and front passenger seats fully forward.
  3. Remove the center console lower rear panel. See Panneau - arrière inférieur - console centrale (retirez et remplacez).
  4. Remove the bolts (x2) that attach the LH and RH rear console carrier to the body.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
  5. Move the driver and front passenger seats fully rearward.
  6. Remove the LH and RH floor mats.
  7. Remove the LH and RH center console side panel carpets. See Tapis - panneau latéral - console centrale - gauche (retrait et remplacement).
  8. Remove the bolt that attaches the LH toeboard lower bracket to the center console. Repeat this step for the RH bracket.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
  9. Release the harness clips (x2), and then disconnect the center console electrical connectors (x4).
  10. Remove the bolts (x2) that attach the LH and RH console carrier center bracket.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
  11. Recline the backrest for the driver and front passenger seats.
  12. With an assistant, remove the console assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift at the rear of the center console, then rotate the front from under the instrument panel, and then remove the center console assembly through the front passenger door.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Do not to scratch the seats, instrument panel, or inner door panel.

Installer

  1. With an assistant, install the console assembly on the vehicle:
    Informational PurposesAn informational icon, calling your attention
    Remarque
    x3 datums
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Carefully maneuver the front of the center console assembly under and into the instrument panel carrier and lower the rear of the center console into place. Align the datums into the instrument panel carrier and engage forward.
  2. Install the bolt that attaches the LH toeboard lower bracket to the center console. Repeat this step for the RH bracket.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
  3. Fasten the harness clips (x2), and then connect the center console electrical connectors (x4).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure all connector locks are engaged.
  4. Install the bolts (x2) that attach the LH and RH console carrier center bracket.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
  5. Install the LH and RH center console side panel carpets. See Tapis - panneau latéral - console centrale - gauche (retrait et remplacement).
  6. Install the LH and RH floor mats.
  7. Move the driver and front passenger seats fully forward.
  8. Install the bolts (x2) that attach the LH and RH rear console carrier.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
  9. Install the center console lower rear panel. See Panneau - arrière inférieur - console centrale (retirez et remplacez).
  10. Restore the driver and front passenger seats back to their original position.
  11. Raise all windows and close all doors.