Code de correction 17107702 17107802 0.36 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

1. Open LH front door

   

2. Raise and support vehicle
   Remarque

   Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads

   

   

   

3. Open hood
   Remarque

   Select Controls > Frunk Open

   

   

4. Remove rear underhood apron
   Remarque

   8x clips

   

   

5. Remove LH underhood apron
   Remarque

   10x clips

   

   

6. Remove RH underhood apron
   Remarque

   10x clips

   

   

7. Remove front underhood apron
   Remarque

   7x clips

   

   

8. Remove frunk access panel
   Remarque

   3x clips, 3x hooks, 1x connector

   

   

9. Remove frunk carpet

   

   

10. Remove frunk assembly
    Remarque

    4x bolts, 10mm, 5 Nm

    

    

11. Disconnect active noise cancellation harness connector from frunk harness
    Remarque

    1x connector, Release locking tab, 1x harness clip, Release clip securing active noise cancellation harness connector onto body

    

    

    

12. Remove LH front wheel cap
    Remarque

    Lift every other spoke at a time until cap is released from rim

    

    

    

13. Loosen LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

    

14. Raise vehicle partially and lower onto locks
    Remarque

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

15. Remove LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

    

16. Release clips securing active noise cancellation harness onto bracket
    Remarque

    2x harness clip

    

    

17. Disconnect active noise cancellation harness connector from sensor and remove harness from vehicle
    Remarque

    1x connect, Release locking tab

    

18. Connect active noise cancellation harness onto sensor
    Remarque

    1x connect, Secure locking tab

    

19. Position active noise cancellation harness into place
    Remarque

    Ensure the harness is routed above the lower links and below the tie rod and halfshaft

    

    

20. Install clips securing active noise cancellation harness onto bracket
    Remarque

    2x harness clip

    

    

21. Install LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

    

    

22. Lower vehicle until tires are touching ground
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

    

23. Torque LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

    

24. Install LH front wheel cap
    Remarque

    Align valve stem with cap

    

    

25. Connect active noise cancellation harness connector to frunk harness
    Remarque

    1x connector, Secure locking tab, 1x harness clip, Install clip securing active noise cancellation harness connector onto body

    

    

    

26. Install frunk assembly
    Remarque

    4x bolts, 10mm, 5 Nm

    

    

27. Install frunk carpet
    Remarque

    Verify carpet is properly seated under the seal

    

    

28. Install frunk access panel
    Remarque

    3x clips, 3x hooks, 1x connector

    

    

29. Install front underhood apron
    Remarque

    7x clips

    

    

30. Install RH underhood apron
    Remarque

    10x clips

    

    

31. Install LH underhood apron
    Remarque

    10x clips

    

    

32. Install rear underhood apron
    Remarque

    8x clips

    

    

33. Close hood
    Remarque

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

    

34. Remove vehicle from lift
    Remarque

    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"

    

    

35. Close LH front door
    Remarque

    Close doors